• what f1 error code means
  
  
  F1 - E1 Safety flip flop Replace Electronic Range Control/Clock (ERC), looked this up on google, hope it helps
  
  
  Was this comment useful?


• F1 - E1 code
  
  
  Not valid for Y line. If there is a Y near the end of your model number, do not use this chart.
  Failure
  Code Condition Check/Repair
  4 Digit Failure Code
  F0 - E0 Analog to Digital Failure Disconnect for 30 seconds - if display re-appears - replace control
  F1 - E1 Safety flip flop Replace Electronic Range Control/Clock (ERC)
  F2 - E0 Shorted keypad Replace Electronic Range Control/Clock (ERC)
  F3 - E0 Oven temperature sensor or oven temperature sensor fuse opened Replace oven temperature sensor or fuse
  F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor
  F3 - E2 Oven too hot Replace oven temperature sensor
  F3 - E3 Clean temp too hot Replace oven temperature sensor
  F5 - E0
  F5 - E1 and E2 Door latch problem Check door/latch switch, replace if necessary
  2 Digit Failure Code
  F0 or F1 or F5 Failed Electronic Range Control (ERC) Replace Electronic Range Control/Clock (ERC)
  F2 - E0 Oven temp too high 1. Test operation of door lock on self-clean models
  2. Test relay contact operation
  3. High resistance in oven temperature sensor
  F3 Open oven temperature sensor or thermal fuse, bad oven temperature sensor harness, or oven temperature sensor resistance too high Replace oven temperature sensor or thermal fuse
  F4 Shorted oven temperature sensor Replace oven temperature sensor
  F6 Problem in time keeping circuit 1. Reset time and/or cooking operation
  2. Check for proper ground
  F7 Stuck function switch or button on Electronic Range Control (ERC) Replace Electronic Range Control/Clock (ERC)
  F8 Failure of Electronic Range Control (ERC) Replace Electronic Range Control/Clock (ERC)
  F9 Door lock circuit Check wiring and test operation of door lock switch
  DOOR Bake or Broil
  · Defective latch switch
  · Shorted wire from ERC 10-pin connector, pin 10 to ground
  · Door latched Replace latch switch if defective.Replace wire from 10-pin connector if defective
  DOOR Self-Clean
  · Defective latch switch
  · Open wire from ERC 10-pin connector, pin 10 to ground
  · Door not latched Replace latch switch if defective.Replace wire from 10-pin connector if defective
  LOCK Not in Self-Clean
  · Oven temperature sensor resistance too high Check oven temperature sensor resistance, wire harness and connections, replace defective component
  
  
  Was this comment useful?


• non y line model chart for F1 error code
  
  
  yours is likely the one that isnt the y line , if so use this chart...
  ROPER
  Range/Stove Oven- Alternative 2 Digit Fault Codes
  Failure
  Code Condition Check/Repair
  F1 Analog to Digital Failure Disconnect for 30 seconds - if display re-appears - replace control
  F1 Safety flip flop Replace component
  F1 Shorted keypad Replace component
  F3 Oven temperature sensor opened Measure oven temperature sensor resistance, should be1100 ohms. If not, replace sensor
  F2 Oven temperature sensor shorted Replace oven temperature sensor
  F3 Oven too hot Replace oven temperature sensor
  F3 Clean temp too hot Replace oven temperature sensor
  F5 Check door/latch switch Replace component
  
  
  Was this comment useful?


• F3 on Frigidaire Oven
  
  
  I am still getting the F3 Error on my frigidaire oven (Model# REG74BF*0) after replacing the temperature sensor. It usually throws the code 20 minutes after the oven has been in use.
  
  
  Was this comment useful?

Add Comment