Broan QP242WW Microwave Oven User Manual


 
MODELS QP230BCQP230BLQP230SSQP230WW
QP236BCQP236BLQP236SSQP236WW
QP242BCQP242BLQP242SSQP242WW
Page 3
3¼” X 10”
HORIZONTAL DUCTING
CABINET
BOTTOM
CABINET FRONT
HORIZONTAL DUCT
ACCESS HOLE
5¼"
5¼"
HOOD
MOUNTING
SCREWS (5)
ELECTRICAL
ACCESS HOLE
(in wall)
4"
CENTER
LINE
WOOD SHIMS
(recessed-bottom
cabinets only)
6
7
/8"
1
3
/8"
3
/8"
*
17
5
/
8
" (42" hood)17
5
/
8
" (42" hood)
14
5
/
8
" (36" hood)14
5
/
8
" (36" hood)
11
5
/
8
" (30" hood)11
5
/
8
" (30" hood)
ELECTRICAL
ACCESS HOLE
(in cabinet bottom)
2
1
/8"
6
7
/8"
10
7
/8"
2
5
/8"
HOOD MOUNTING SCREWS (5)
4
5
/8"
8" DIA.
HOLE
7-IN. ROUND
DUCT
ACCESS
HOLE
7-IN. ROUND
DUCT
ACCESS
HOLE
11"
17
5
/
8
" (42" hood)17
5
/
8
" (42" hood)
14
5
/
8
" (36" hood)14
5
/
8
" (36" hood)
11
5
/
8
" (30" hood)11
5
/
8
" (30" hood)
*
7-IN. ROUND
DUCTING
2 Use the proper diagram below, for placement of ductwork
and electrical cutout in cabinet or wall. For a non-ducted
installation, DO NOT cut a duct access hole.
VERTICAL DUCT
ACCESS HOLE
¾"
10
7
/
8
"
5¼"
5¼"
CENTER
LINE
HOOD MOUNTING SCREWS (5)
ELECTRICAL
ACCESS HOLE
(in cabinet bottom)
WOOD SHIMS
(recessed-bottom
cabinets only)
CABINET FRONT
CABINET
BOTTOM
17
5
/
8
" (42" hood)
4½"
2
1
/
8
"
2
5
/
8
"
11"
6
7
/
8
"
*
17
5
/
8
" (42" hood)
14
5
/
8
" (36" hood)14
5
/
8
" (36" hood)
11
5
/
8
" (30" hood)11
5
/
8
" (30" hood)
3¼” X 10”
VERTICAL DUCTING
PREPARE HOOD LOCATION
SOFFIT
24" - 30" ABOVE
COOKING SURFACE
CABINET
3¼" X 10" DUCT
(For horizontal discharge)
WALL CAP
ROOF CAP
3¼" X 10" or
7" ROUND DUCT
(For vertical
discharge)
HOUSE WIRING
(Top or Back of hood)
HOODHOOD
1 Determine whether hood will discharge vertically (3¼”
x 10” or 7” Round), or horizontally (3¼” x 10” only). For
vertical or horizontal discharge, run ductwork between
the hood location and a roof cap or wall cap. For best
results, use a minimum number of transitions and
elbows.
FUSE
The Range Hood Control Board contains a Fuse to protect the
controls from power surges. If the fuse has opened (blown), the
green fan setting or light setting indicators will not operate properly
when the fan or light buttons are pressed, and the fan and lights
will not turn on.
A new fuse can be purchased at your local electronic supply
store. Use an 8A, 120V, 5 mm diameter, 20 mm long, fast-acting,
cartridge-type fuse.
To replace the fuse:
1. Disconnect power at service entrance.
2. Remove filters and bottom pan.
3. Remove and inspect fuse. If it is not open (blown), additional
diagnostics are needed.
FUSE
RANGE HOOD CONTROL BOARD
*
Note the extra wood shim and mounting screw near the
cabinet front, on the cabinet center line.