Emerson EM229 Bluetooth Headset User Manual


 
NOTE: This headset is capable of pairing to two mobile
phones at the same time.
Pairing a second phone (Multi-Link)
1. Make sure the headset is turned ON and connected to the
rst phone.
2. Press and HOLD the [Volume Down] button for 3 seconds
or until the headset’s indicator light ashes RED and BLUE
alternately.
3. The headset is now in Pairing Mode and is ready to connect
to your second mobile phone.
4. Set your second mobile phone to search for Bluetooth
devices.
5. When the second phone nds the headset, conrm by
selecting EM229 from the list.
6. Enter passcode “0000” when prompted by the second phone
OR
depending on which model phone you are trying to connect
the headset to, it may not be necessary to enter a passcode.
Select “Pair” to complete the pairing process.
7. Your mobile phone will conrm that the pairing process
was completed. Select “Yes” to connect the headset to
your second mobile phone. If the pairing was successful,
the headset’s indicator light turns to standby mode and
ashes once every three seconds.
8. After pairing the second phone, by default the rst phone
will be disconnected from the headset. Enter the rst
phone’s Bluetooth settings screen and connect it to the
headset. Both phones should now be connected to the
headset.
Switching calls between two connected phones
1. While on a call with one phone and the second phone rings
with an incoming call, press and HOLD the [Volume Up]
button briey to answer the 2nd call and place the rst
phone on hold.
2. Press and HOLD the [Volume Up] button briey to switch
between the two phones and place the current phone on
hold.
3. To hang up the current call, press the [Call] button. The
headset will end the current call and return to the other
phone which was placed on hold.
4. To end that call, press the [Call] button or press the [End]
key on your phone.
NOTE: Charge the headset for at least 8 hours before using it
for the rst time, even if the RED LED indicator shuts o.
Model: EM229
Owner’s Manual
WIRELESS HEADSET
Charging
Socket
USB cable
Headset
NOTE: To enter Pairing Mode at any time, you must press and
HOLD the [Call] button for approximately 10 seconds.
5. Set your mobile phone to search for Bluetooth devices.
Searching for devices
Paired Devices:
1 f
ound
Stop
*Empty *
Bluetooth: Enabled
OR depending on which model mobile phone you are trying
to connect the headset to, it may not be necessary to enter a
passcode and the following message (or similar) may appear on
your phone’s display.
Enter numeric passkey
for EM229:
Paired Devices:
0000
OK
EM229
Bluetooth: Enabled
Select “Pair” to complete the pairing process.
“EM229” would like to pair
with your phone. Would you
like to allow it to pair?
Paired Devices:
Cancel Pair
EM229
Bluetooth: Enabled
8. Your mobile phone will conrm that the pairing process was
completed and prompt you to accept the connection.
Please select “YES” to connect the headset to your mobile
phone. If the pairing was successful, the headset’s indicator
light turns to standby mode and ashes once every three
seconds.
NOTE: The screenshots above are typical of many Bluetooth
enabled phones in the market today, and are used to
assist in the explanation of the pairing process. Your
mobile phone’s or Bluetooth enabled device’s interface
and interaction with the headset may be slightly
dierent from the illustrations shown.
9. When attempting to reconnect the headset to your mobile
phone, you may see the message below and your mobile
phone will prompt you to accept the connection request to
the EM229 headset, and an option not to ask this again.
Please accept the connection, and if you select “Don’t ask this
again”, your phone will automatically accept future connection
requests from the headset.
Confirm connection to
EM229?
Paired Devices:
YES NO
EM229
Bluetooth: Enabled
/
Accept connection request
from EM229?
Paired Devices:
YES NO
EM229
Bluetooth: Enabled
/
Don’t ask this again
CAUTION: Although this device enables drivers to
conduct handsfree conversations, it is still safer to pull
over before using a mobile phone.
Always keep your full attention on your driving.
Driving while talking on your mobile phone is dangerous, and
illegal in many states.
Check local laws regarding the use of a mobile handset and wireless
headset while driving. If you use the Bluetooth Headset while
driving, ensure your attention and focus remains on your driving.
Please use your mobile phone, and our
product responsibly while driving!
1. Connect the charging pin of the USB cable to the charging
socket of the headset.
2. Connect the other end of the USB cable to either the:
• AC Charger, and plug into a wall (A/C) outlet
• Computer’s USB port
• Car Charger
3. The RED LED indicator light turns on while the headset is
charging.
4. The RED LED indicator light shuts o when the headset is
fully charged (approximately 2-3 hours).
NOTE: When the battery is running low, the RED LED indicator
light starts to ash along with a warning beep.
Car ChargerPCAC Charger
Earhook
Owner’s
Manual
USB charging
cable
AC charger
Silicone cushions
S M L
Car Charger
Easy Pairing
(First time pairing only)
Please read through this section before turning the
device on.
This Bluetooth headset has an “Easy Pairing” feature which
sets the headset to Pairing Mode the rst time the power
switch is turned on.
1. Make sure the Bluetooth Headset is within 3 feet of
your mobile phone or Bluetooth enabled device.
2. Set the [Power] switch to the ON position. The indicator
light should be ashing RED and BLUE alternately,
indicating the headset is in Pairing Mode and ready to
connect to your Bluetooth enabled device.
3. Continue to “Manual Pairing” step 5 shown below.
Note: Manual Pairing
If the rst time pairing was unsuccessful or for
future pairing, you will need to manually pair the
headset to your Bluetooth enabled device (see
“Manual Pairing” below).
Charging
socket
Speaker/
Silicone cushion
Microphone
Indicator light
Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
Volume up
(Press 3 seconds to redial)
Volume down
Call button
Answer/end a call
Bluetooth
Headset
6. When the phone nds the headset, conrm by selecting
EM229 from the list.
Select Device:
Paired Devices:
EM229
Cancel
EM229
Bluetooth: Enabled
7. Enter the passcode “0000” when prompted by the phone.
Press & hold
to pair 2nd phone
Manual Pairing
1. Make sure the Bluetooth Headset is within 3 feet of your
mobile phone or Bluetooth enabled device.
2. Set the [Power] switch to the ON position.
3. Press and HOLD the [Call] button until the indicator light
ashes RED and BLUE alternately.
4. The headset is now in Pairing Mode and is ready to connect
to your mobile phone or Bluetooth enabled device.
within 3 feet
Indicator light
Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
Press & Hold
to switch calls
Call button
within 3 feet
Indicator light
Model: EM229
Owner’s Manual
WIRELESS HEADSET
Indicator
light
In the boxIn the boxIn the boxIn the boxIn the box Charging the headsetCharging the headset
Location of controlsLocation of controls
Drive SafeDrive Safe Pairing the headsetPairing the headset
Pairing the headset with a 2nd mobile phonePairing the headset with a 2nd mobile phone