Filter
Top Products
ERUTAREPMETNOITCNUF
YOUR OVEN
OB60SL9DEX
THE CONTROL PANEL
FIRST USE
1 REMOVE ALL CABLE TIES & PACKAGING HOLDING
THE SHELVING IN PLACE
3 REMOVE BOTH SIDE RACKS
2 REMOVE ALL SHELVES FROM THE OVEN
Keep this document handy for easy reference.
For detailed information on the other features of your oven, see your ‘User guide’.
Before using your oven, make sure you read the full ‘User guide’, with special attention to the ‘Safety and warnings’ section.
For contact information or if you require service, assistance or replacement parts, see the end of this document or your ‘Service & warranty’
booklet.
NZ AU GB IE
QUICK START GUIDE
Built-in oven
1
Control panel
2
Oven vent louvres
3
Step down oven wire shelf
4
Oven light
5
Telescopic sliding shelf
6
Side rack
7
Oven wire shelf
8
Oven door and handle
9
Oven seal
Accessories:
10
Grill rack
11
Smokeless grill tray
12
Deep Roasting dish
13
Flat baking tray
14
Catalytic panels
10
11
12
13
14
2
3
4
5
6
7
retaining wire
lock stud
8
1
9
Important!
Before using your oven for the first time, you should fit both
the Catalytic Panels (supplied). See ‘Care and cleaning’ in
your user guide for details about these self cleaning panels.
You do this by:
removing ALL the cable ties holding the shelving in place,
if the installer has not already done so.
removing the shelves and side racks
fitting the catalytic panels
replacing the side racks and shelves
We recommend you then condition the oven.
Follow the steps below to fit the Catalytic Panels.
1
Remove all the shelving, taking special care with the telescopic
sliding shelves.
2
To remove a telescopic sliding shelf, grip it at the front (making
sure you are gripping the wire shelf and the sliding frame
together), lift upwards and pull it out of the oven.
For your safety, the wire shelf and telescopic sliding frame are
built together as one unit and are not separable.
Remove both side racks by 1)
pushing down on the retaining
wire until it clears the lower lock
stud and swing out wards to 2)
clear the upper lock studs, then
3) lift out.
1
3
2
2
Function indicators
(see ‘Oven functions’)
Function dial Temperature
indicator
Temperature
dial
Function halo
Temperature
halo
Timer indicator
(see ‘Using the
timer’)
if lit:
Timer is counting
down
Rotisserie indicator
(see ‘Using the
Rotisserie’) in the
User guide
if lit:
Rotisserie is
in use
Cooking time indicator (see ‘Automatic cooking’) in User guide
if lit:
Automatic cooking time is set
Stop time indicator
(see ‘Automatic cooking’) in User guide
if lit:
Automatic stop time is set
Display
Scroll Select Cancel
continued over
SETTING THE CLOCK
You set the clock within the user preference menu. To learn more about the user preference menu, refer to your User guide.
Note: If you do not wish to set the time initially when the oven is first switched on at the wall, press the cancel
button to exit the clock setting.
If you want to set the clock later, follow the steps under ‘To change the time’.
When the oven is first switched on at the wall
3
Press the left and right scroll
buttons to set the time.
1
The display will flash 24 Hr.
4
Press the select
button to confirm.
The time set will now be steadily lit.
2a
Press the right scroll button to scroll
between
24 Hrand 12 Hr
2b
Press the select
button to confirm.
To change the time
(within the user preference menu)
Locking the control panel
To lock, press and hold the select
button for 2 seconds.
To unlock, press and hold the
cancel button for 2 seconds.
Control lock indicator (see
‘Locking the control panel’)
if lit:
Control panel is locked
1
Press and hold the left and right scroll
buttons together for 3 seconds
to enter the user preference menu.
The display will either show 12 Hror 24
Hr
2
Press the select
button to confirm.
The display will flash.
3
Follow steps 2-5 left to set the time.
At step 2a, you also now have the
ability to scroll between
24 Hr,
12 Hr and OFF (turns the display off).
Refer to the User guide to learn more
about this feature.