GE Monogram ZBD6920PSS Dishwasher User Manual


 
Dimensions and Specifications (in inches)
• The dishwasher must be installed so that the drain hose
is no more than 10 feet in length for proper drainage.
• Water and power supply should enter in the
shaded area.
• Electrical and water connections are at the right front
of the dishwasher. The hot water line should extend
forward 30" to 40" from the rear wall. The electrical
must extend forward at least 24" to reach the junction
box.
• To prevent siphoning, an air gap must be used when
the waste tee or disposer connection is less than 18"
above the floor.
Cabinets
Square
and
Plumb
Floor MUST
be Even with
Room Floor
This Wall Area
must be Free of
Pipes or wires
34-1/2" Min.
Underside of
Countertop
to Floor
24"
Min.
24" Min.
5" 5"
4"
4"
6"
24"
*24"
34"
Adjustable
to 35"
Electrical Requirements
The dishwasher must be supplied with 120V, 60Hz, and
connected to an individual properly grounded branch
circuit protected by a 15- or 20-amp circuit breaker or
time-delay fuse.
Custom Panel for Model ZBD6900PII
These dishwashers require a eld installed 3/4” thick custom
panel and custom handle. An installation template is
packed with these models and may be obtained in advance.
Order Pub. No. 31-30569-1. Complete panel installation
instructions are included on the template.
CUSTOM PANEL SIZE REQUIREMENTS
HEIGHT
Panel height must
be between
30-1/16" and 30-1/4".
If the panel height is
more than 30-1/4” it
will prevent the door
from swinging open.
If the panel height is
less than 30-1/16” it
will not cover the
dishwasher door
frame.
The top of the custom panel must be ush with the top
of the door. The 1/2” minimum gap between the top
of the door and the bottom of the countertop must be
maintained.
WIDTH
Panel width must be 23-3/4".
If the panel width is less than
23-3/4” it will not cover the
dishwasher frame.
IMPORTANT: To ensure
optimum door balance
performance, the custom panel must not weigh
more than 14 lbs.
Accessories for custom panel model ZBD6900
ZPR0700S door panel provides a professional-style handle
on a stainless steel door panel.
ZTB700 stainless steel tubular handle for installation onto a
custom panel.
Before installing refer to installation instructions for
details. Pub. No. 31-30586
Minimum 1/2" Gap
for Clearance
Countertop
1/2" min.
23-3/4"
30-1/16" Min.
30-1/4" Max.
Minimum 1/2" Gap
for Clearance
Countertop
1/2" min.
23-3/4"
30-1/16" Min.
30-1/4" Max.
ZBD6920PSS/ZBD6910PBB/ZBD6900PII
GE Monogram
®
Fully Integrated Built-In Dishwashers
For answers to your Monogram,
®
GE Profile
or
GE
®
appliance questions, visit our website at
ge.com or call GE Answer Center
®
service,
800.626.2000.
Specification Created 8/08
150051
As an ENERGY STAR
®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.
Listed by
Underwriters
Laboratories
* Dishwasher models
ZBD6900 and ZBD8900
require a 3/4" thick
custom panel and will be
24-3/4" deep.