Primo Water 900199 Water Dispenser User Manual


 
INSTALLING WATER BOTTLE
1. Place dispenser on a level counter top.
2. Remove tamper evident seal from plastic bottle cap. Do
NOT remove plastic cap.
3. Clean bottle cap and neck with a cloth and warm soapy
water, then rinse.
4. Lift bottle and insert onto the probe. Apply slight pressure
until the plug inside the cap pushes in and the bottle is
seated. Water will begin to flow into the tank causing air
bubbles in the bottle.
DISPENSING WATER
3. Place glass below spout.
4. Push control in to dispense water. Release to stop.
TROUBLESHOOTING
Water is leaking.
Bottle may have a leak. Remove and install new bottle.
If leak remains, remove bottle and call 866-429-7566 for
assistance.
No water is coming from the spout.
Make sure the bottle is not empty. If empty, replace it.
Make sure to push the control in fully.
Water tastes bad.
Dispenser may be dirty. Remove bottle and empty tank.
Wipe bottle receptacle, tank and spout with a cloth wetted
with bleach. Then rinse with clean water and dry.
Dispenser is dirty.
Wipe body, bottle receptacle, tank and spout with a cloth
wetted with bleach. Then rinse with clean water and dry.
PN O-061 © 2010 Primo Water Corporation
LIMITED WARRANTY
Primo Water Corporation, (“Vendor”) warrants to the original purchaser of
this dispenser, and to no other person, that if this dispenser is assembled
and operated in accordance with the printed instructions accompanying it,
then for a period of one (1) year from the date of purchase, all parts in such
dispenser shall be free from defects in material and workmanship. Vendor
may require reasonable proof of your date of purchase from an authorized
retailer or distributor. Therefore, you should retain your sales slip or invoice.
The Limited Warranty shall be limited to repair or replacement of parts,
which prove defective under normal use and service and which Vendor shall
determine in its reasonable discretion upon examination to be defective.
Before returning any parts, you should contact Vendor’s Customer Service
Department using the contact information listed below. If Vendor confirms,
after examination, a defect covered by this Limited Warranty in any returned
part, and if Vendor approves claim, Vendor will replace such defective part
without charge. If you return defective parts, transportation charges must be
prepaid by you. Vendor will return replacement parts to original purchaser,
freight or postage prepaid.
The Limited Warranty does not cover any failures or operating difficulties
due to accident, abuse, misuse, alteration, misapplication, improper
installation or improper maintenance or service by you or any third party, or
failure to perform normal and routine maintenance on the dispenser, as set
out in the User’s Manual. In addition, the Limited Warranty does not cover
damages to the finish, such as scratches, dents, discoloration or rust after
purchase.
The Limited Warranty is in lieu of all other express warranties. Vendor
disclaims all warranties for products that are purchased from seller other
than authorized retailers or distributors. AFTER THE PERIOD OF THE ONE (1)
YEAR EXPRESS WARRANTY, VENDOR DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FURTHER,
VENDOR SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY
THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR
CONSEQUENTAL DAMAGES. Vendor assumes no responsibility for any
defects caused by third parties. This Limited Warranty gives the purchaser
specific legal rights; a purchaser may have other rights depending upon
where he or she lives. Some jurisdictions do not allow exclusion or limitation
of special, incidental or consequential damages, or limitations on how long a
warranty lasts, so the above exclusion and limitations may not apply to you.
Primo Water Corporation
104 Cambridge Plaza Drive, Winston-Salem, NC 27104
866-429-7566
www.PrimoWater.com
Water Bottle
Not included.
Uses 3, 4 or 5 gallon bottles.
Visit www.PrimoWater.com to find
Primo Water at a store near you.
Bottle Receptacle
Includes a probe that eliminates spills
when loading bottles. Twists on & off
to allow easy cleaning of tank.
Control
Push in to dispense water. Release to
stop.
Spout
Water comes out here.
Base
Includes non-slip feet that won’t mar
countertops.
FEATURES & FUNCTIONS
Spill Proof
Tabletop
Water Dispenser
Models 900131, 900196
and 900199
TO REDUCE THE RISK OF INJURY AND PROPERTY
DAMAGE, USER MUST READ THIS MANUAL
BEFORE ASSEMBLING, INSTALLING & OPERATING
DISPENSER.
SAVE THIS MANUAL FOR FUTURE USE
Please visit www.PrimoWater.com for more useful information, instructional videos, tips and special offers.
IMPORTANT: Do Not Return Dispenser to Store. If you have questions or issues please contact 1-866-429-7566 for expert assistance.
GETTING STARTED
1. Remove carbon bag from bottle receptacle.
2. Remove bottle receptacle by turning counterclockwise and
then lifting.
3. Wipe bottle receptacle, tank and spout with a cloth wetted
with bleach. Then rinse with clean water and dry.