1. Manuals
  2. Kitchen Appliance Support
  3. Frigidaire Support
  4. Range Support
Support User Manuals
Question About Frigidaire Range Electric Range
Oven won't turn off...

The oven won't turn off. I have to unplug the range overnight to reset it. I think I saw code F1 and am wondering what that might mean.

Asked by Kathleen on 10/06/2008 5  Answers

ManualsOnline posted an answer 16 years ago

The ManualsOnline team has found the manual for this product! We hope it helps solve your problem. Get the Manual Here

Donald posted an answer 15 years, 10 months ago

5 I am still getting the F3 Error on my frigidaire oven (Model# REG74BF*0) after replacing the temperature sensor. It usually throws the code 20 minutes after the oven has been in use.
Was this answer helpful?

June posted an answer 16 years ago

4 F1 - E1 Safety flip flop Replace Electronic Range Control/Clock (ERC), looked this up on google, hope it helps
Was this answer helpful?

June posted an answer 16 years ago

0 Not valid for Y line. If there is a Y near the end of your model number, do not use this chart. Failure Code Condition Check/Repair 4 Digit Failure Code F0 - E0 Analog to Digital Failure Disconnect for 30 seconds - if display re-appears - replace control F1 - E1 Safety flip flop Replace Electronic Range Control/Clock (ERC) F2 - E0 Shorted keypad Replace Electronic Range Control/Clock (ERC) F3 - E0 Oven temperature sensor or oven temperature sensor fuse opened Replace oven temperature sensor or fuse F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor F3 - E2 Oven too hot Replace oven temperature sensor F3 - E3 Clean temp too hot Replace oven temperature sensor F5 - E0 F5 - E1 and E2 Door latch problem Check door/latch switch, replace if necessary 2 Digit Failure Code F0 or F1 or F5 Failed Electronic Range Control (ERC) Replace Electronic Range Control/Clock (ERC) F2 - E0 Oven temp too high 1. Test operation of door lock on self-clean models 2. Test relay contact operation 3. High resistance in oven temperature sensor F3 Open oven temperature sensor or thermal fuse, bad oven temperature sensor harness, or oven temperature sensor resistance too high Replace oven temperature sensor or thermal fuse F4 Shorted oven temperature sensor Replace oven temperature sensor F6 Problem in time keeping circuit 1. Reset time and/or cooking operation 2. Check for proper ground F7 Stuck function switch or button on Electronic Range Control (ERC) Replace Electronic Range Control/Clock (ERC) F8 Failure of Electronic Range Control (ERC) Replace Electronic Range Control/Clock (ERC) F9 Door lock circuit Check wiring and test operation of door lock switch DOOR Bake or Broil · Defective latch switch · Shorted wire from ERC 10-pin connector, pin 10 to ground · Door latched Replace latch switch if defective.Replace wire from 10-pin connector if defective DOOR Self-Clean · Defective latch switch · Open wire from ERC 10-pin connector, pin 10 to ground · Door not latched Replace latch switch if defective.Replace wire from 10-pin connector if defective LOCK Not in Self-Clean · Oven temperature sensor resistance too high Check oven temperature sensor resistance, wire harness and connections, replace defective component
Was this answer helpful?

June posted an answer 16 years ago

0 yours is likely the one that isnt the y line , if so use this chart... ROPER Range/Stove Oven- Alternative 2 Digit Fault Codes Failure Code Condition Check/Repair F1 Analog to Digital Failure Disconnect for 30 seconds - if display re-appears - replace control F1 Safety flip flop Replace component F1 Shorted keypad Replace component F3 Oven temperature sensor opened Measure oven temperature sensor resistance, should be1100 ohms. If not, replace sensor F2 Oven temperature sensor shorted Replace oven temperature sensor F3 Oven too hot Replace oven temperature sensor F3 Clean temp too hot Replace oven temperature sensor F5 Check door/latch switch Replace component
Was this answer helpful?

Add Your Answer

Please Note: Do not submit personal information as it will be displayed online.
Ask a Question Request a Manual