Filter
Top Products
10
Multiple Heating Stages
Oven can be programmed to perform 4 independent
heating cycles without interruption.
1. Open oven door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If dooris closed or
RESET
pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press pad
1
for approximately 15 seconds.
• After 15 seconds, signal sounds. Display shows
“Pb” or “Pd” indicating “b” or “d” menu.
3. Press
MENU
pad to select preprogrammed menu if
necessary.
4. Press desired number pad.
• Display shows heating time and power level if less
than 100 percent power.
5. Press number pads to enter desired cooking time.
• For example, to heat for 2 minutes 30 seconds,
press
2
,
3, and 0
pads.
6. Press a power level pad if power level less than 100
percent is required.
• Display shows current power level if less than 100
percent power.
• To restore power level to 100 percent, reenter
cooking time.
8. Press
TIME ENTRY
pad.
• Display briefly shows "bP1
(1-9,0)
" or "dP1
(1-9,0)
"
indicating menu, programming, stage, and pad.
Then cook time and power level for stage show in
display.
• Repeat steps 5-8 to create additional stages.
9. Press
START
pad to save new heating time and
power level in oven memory.
10. Press
RESET
pad or close oven door to exit
programming mode.
Deactivating Control Panel
1. Open oven door, and close oven door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If pad is not pressed in 30 seconds, open and
close oven door again.
2. Press
TIME ENTRY
pad.
• Display shows “0000” and “READY”.
3. Press
1,3,5,
and
7
pad in sequence.
4. Press
TIME ENTRY
pad.
• “LOC” and “READY” show in display.
• All pads except
TIME ENTRY
are disabled.
• To reactivate control repeat steps 1-4.
Deactivating Preprogrammed Pad
1. Open oven door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If dooris closed or
RESET
pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press and hold pad
1
for approximately 15 seconds.
• After 15 seconds, signal sounds. Display shows
“Pb” or “Pd” indicating “b” or “d” menu.
3. Press desired number pad.
• Display shows heating time and power level if less
than 100 percent power.
4. Press hidden pad.
•“
dddd
” and pad number show in display.
5. Press
START
pad to save in oven memory.
• To reactivate pad, repeat steps.
6. Press
RESET
pad or close oven door to exit
programming mode.
Reactivating Preprogrammed Pad
1. Open oven door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If dooris closed or
RESET
pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press and hold pad
1
for approximately 15 seconds.
• After 15 seconds, signal sounds. Display shows
“Pb” or “Pd” indicating “b” or “d” menu.
3. Press desired number pad.
• Display shows heating time and power level if less
than 100 percent power.
4. Press hidden pad.
• Display shows “0000” and “READY”.
5. Program pad according to “Preprogrammed Number
Pads” section step 5-8.
6. Press
START
pad to save in oven memory.
• To reactivate pad, repeat steps.
7. Press
RESET
pad or close oven door to exit
programming mode.