Amana W10310515A Dishwasher User Manual


 
4
Rinse aid keeps water from forming droplets that can
dry as spots or streaks. They also improve drying by
allowing water to drain off of the dishes after the final
rinse.
Rinse aid helps to reduce excess moisture on the
dish racks and interior of your dishwasher.
Check the rinse aid indicator. Add rinse aid when indicator
drops to “Add” level or, when rinse aid indicator looks light. A
light visual indicator means to add rinse aid, and a dark visual
indicator means that there is sufficient rinse aid in the
dishwasher.
Dispenser with one lid - To add
rinse aid, turn the dispenser
cap to “Refill” and lift off. Pour
rinse aid into the opening until
the indicator level is at “Full.”
Replace the dispenser cap and
turn to “Lock.” Make sure cap
is fully locked.
NOTE: For most water conditions, the
factory setting of 2 will give good
results. If you have hard water or notice
rings or spots, try a higher setting. Turn
the arrow adjuster inside the dispenser
by either using your fingers or inserting
a flat-blade screwdriver into the center
of the arrow and turning.
Select a Cycle
NOTE: Heavier cycles and options affect cycle length. Some
cycles and options will take up to 3¹⁄₂ hours to complete.
Heavy – Use for heavily soiled, hard-to-
clean items.
Normal – Use for normal food soil. The
energy usage label is based on this cycle.
1-Hour Wash – Use for lightly soiled items.
For fast results, 1-Hour Wash will clean using
slightly more water and energy.
Select Options
You can customize your cycles by
pressing the options desired.
Hi-Temp Wash – (use only with Heavy
and Normal wash cycles) heats the
water during the wash portions of the
cycle.
Heated Dry – (automatic with all except rinse cycle) use for best
drying results. Turn off by pressing HEATED DRY so that the light
goes off.
4-Hour Delay – (any cycle) offers the choice to start the
dishwasher automatically at a later time. Select a wash
cycle and options. Press START/RESUME. Close the
door firmly.
Locked – (on 4-Hour Delay button) use to avoid
unintended use of your dishwasher. When Control Lock
is lit, all buttons are disabled. The dishwasher door can be opened
while the controls are locked.
To turn on Lock:
Press and hold 4-HOUR DELAY for 3 seconds. The Locked light
glows. If you press any pad while your dishwasher is locked, the
light flashes 3 times.
To turn off Lock:
Press and hold 4-HOUR DELAY for 3 seconds. The Control Lock
light turns off.
Start or Resume a Cycle
Run hot water at the sink nearest your dishwasher until the
water is hot. Turn off water.
Push door firmly closed. The door latches
automatically. Select the wash cycle and options
desired OR press START/RESUME to repeat the
same cycle and options as in the previous wash
cycle.
You can add an item anytime before the main wash starts.
Open the door slowly and add the item. Close the door firmly.
Press START/RESUME.
Cycle status indicators allow you to follow the
progress of your dishwasher cycle. Clean indicator
glows when the cycle is finished.
or
Dispenser with two lids - To add rinse
aid, press the cover release button to
open the cover. Fill the dispenser with
rinse aid up to the dotted line. Close
the cover.
A. Cover release button
STEP 3
Full
Add
¹⁄₄
turn
to lock
Lock
Refill
6
5
4
3
2
-
-
-
max
fill
1
-
-
-
-
-
-
-
-
-
-
-
A
6
5
4
3
2
-
-
-
max
fill
1
-
-
-
-
-
-
-
-
-
-
-
-
STEP 4