Filter
Top Products
4
ARISTON DISHWASHER - Instructions for installation and use
D
ISHWASHER
First of all.
After performing all the operations
described in the previous para-
graphs, turn the water tap on com-
pletely, open the appliance door and
press ON-OFF button "A": indica-
tor light "B" comes on. Your appli-
ance is now on and awaiting instruc-
tions.
Selecting the wash
cycle.
Select the wash cycle by pressing
button "P". Each time this button is
pressed, one of the indicator lights
"M" will come on in sequence, se-
lect the wash cycle you deem most
suitable for the type of dishes to
wash (take a look at page 6, where
you will find the wash cycle table).
Close the appliance door and after
a few seconds, you will hear a short
beep: the wash cycle has begun.
Modifying a wash cycle in
progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress, if it has
only just started. Open the appli-
ance door carefully to avoid any
hot water splashes, then keep but-
ton "P" pressed for approximately
5 seconds, until you hear 3 short
beeps. Indicator light "M" will come
off and at this point, all the settings
will have been cancelled. You are
now free to re-set the correct wash
cycle.
You've left out a dish?
Well, it happens to everyone. Inter-
rupt the wash cycle by opening the
appliance door with the utmost
care, as usual, then insert the dish
you had forgotten. When you shut
the appliance door, the cycle will
start up from where you interrupted
it.
Finished?
The end of the wash cycle is indi-
cated by a double beep and the flash-
ing of the wash cycle indicator light
"M". Open the dishwasher door,
press the ON-OFF button as well,
thus cutting off the electricity sup-
ply to the appliance.
Turn off the water tap.
Wait a few minutes before unload-
ing the dishes: they are very hot! If
you wait a little while, they dry
better thanks to the steam. Empty
the lower rack first.
There's been a power
failure? Have you
opened the dishwasher
door?
The wash cycle stops and then
restarts when the electricity comes
back on or when you close the door.
Everything is under control!
You decide when it
starts.
When you have loaded the dishes,
you can choose when to start your
dishwasher before setting the wash
cycle desired.
Press button "C" to delay the start
of the wash cycle by 2, 4 or 6 hours.
Each time you press it, you will
hear a short beep and indicator light
"D" corresponding to the selected
delay will come on.
Now you can select the desired
wash cycle.
Close the appliance door and, after
you hear the beep, the countdown
to the delayed start will begin.
If, for example, you have set the
delayed start to 6 hours, the 6 hour
indicator light will flash, then the 4
hour indicator light will flash, and
finally the 2 hour indicator light. A
quick look at the indicator lights
will keep you informed of the
countdown progress at all times.
Once this time is up, indicator light
"D" will stop flashing and the wash
cycle will begin.
Have you changed your
mind?
If you change your mind and you
wish to set a different delay, just
open the appliance door, press
button "C" and repeat the selection.
If on the other hand you want to
cancel the delay set and you wish
You have loaded your dishes and you now have
to set the wash cycle. It takes just one minute
to learn how
Starting the dishwasher
Make sure the
wash cycle has
ended before
removing the
dishes!
to start the wash cycle
immediately, press the button in
sequence until indicator light "D"
comes off.
Once you close the appliance door,
the wash cycle set previously will
begin.
You want to wash on
one rack only?
Remember to use half
the amount of
detergent.
Your dishwasher also allows you to
wash half a load, to save water and
electricity. Before setting any wash
cycle whatsoever, press button "Q"
repeatedly to select whether you
want to run a half cycle on the up-
per or lower rack. Each time you
press it, you will hear a short beep
and indicator light "R" correspond-
ing to the selected rack will come
on.
Ready, steady, go!
If you have
delayed the start
of your wash
cycle, it is best if
you do not modify
anything while you
wait during the
countdown.
If you really have
to, then press
button "P" and
keep it pressed
down for
approximately 5
second You will
hear 3 short beeps
and all the settings
will be cancelled.
You can now
repeat the
programming
operations.
Do you want extra
drying?
Press button "E" before you start
the selected wash cycle.
A prolonged beep will inform you
that you have selected extra drying,
a short beep indicates it has been
disabled.
With extra drying, the wash cycle
will last longer, to provide you with
drier dishes.