Filter
Top Products
ARISTON DISHWASHER - User Manual 5
www.aristonappliances.us
You have loaded your dishes and you now have to set
the wash cycle. It takes just one minute to learn how
Starting the dishwasher
Ready, steady, go!
You can cancel the
wash cycle in progress,
if it has only just started.
Make sure the wash
cycle has ended before
removing the dishes!
Selecting the wash cycle.
Select the wash cycle by
pressing button "P". Each
time this button is pressed,
one of the indicator lights
"M" will come on in
sequence, select the wash
cycle you deem most
suitable for the type of
dishes to wash (take a look
at page 7, where you will
find the wash cycle table).
Close the appliance door
and after a few seconds,
you will hear a short beep:
the wash cycle has begun.
Modifying a wash cycle in
progress.
If you have chosen the
wrong cycle, not to worry!
You can modify the wash
cycle in progress, if it has
only just started. Open
the appliance door
carefully to avoid any hot
water splashes, then
keep button "P" pressed
for approximately 5
seconds, until you hear a
short beep. Indicator light
"M" will come off and at
this point, all the settings
will have been cancelled.
You are now free to re-set
the correct wash cycle.
You've left out a dish?
Well, it happens to
everyone. Interrupt the
wash cycle by opening the
appliance door with the
utmost care, as usual,
then insert the dish you
had forgotten. When you
shut the appliance door,
the cycle will start up from
where you interrupted it.
Finished?
The end of the wash cycle
is indicated by a double
beep and the flashing of the
wash cycle indicator light
"M". Open the dishwasher
door, press the ON-OFF
button as well, thus cutting
off the electricity supply to
the appliance.
If accessible turn off the
water tap.
Wait a few minutes before
unloading the dishes: they
are very hot! If you wait a
little while, they dry better
thanks to the steam.
Empty the lower rack
first.
There's been a power
failure? Have you opened
the dishwasher door?
The wash cycle stops and
then restarts when the
electricity comes back on
or when you shut the door.
Everything is under control!
Do you want extra drying?
Press button "E" before
you start the selected
wash cycle. A long beep will
tell you that you have
selected extra drying and
the wash cycle will last
longer in order to provide
you with drier dishes.
After performing all the
operations described in the
previous paragraphs, if
accessible turn the water
tap on, open the appliance
door and press on-off
button "A": indicator light
"B" comes on.
Your appliance is now on
and awaiting instructions.
If opening the
door soon
after the end
of the program, or
during it, stand away
from the Dishwasher,
to avoid possible
injury from hot steam.
You decide when it starts.
When you have loaded the
dishes, you can choose
when to start your
dishwasher before setting
the desired wash cycle.
Press button "C" to delay
the start of the wash cycle
by 2, 4 or 6 hours. Each
time you press it, you will
hear a short beep and
indicator light "D"
corresponding to the
selected delay will come
on.
Now you can select the
desired wash cycle. Close
the appliance door and,
after you hear the beep,
the countdown to the
delayed start will begin.
Once this time is up, the
indicator light will stop
flashing and the wash
cycle will begin.
If you change your mind
and you wish to set a
different delay, just open
the appliance door, press
button "C" and repeat the
selection.
If, on the other hand, you
want to cancel the delayed
start set and you want the
wash cycle to start
immediately, press the
button repeatedly until
indicator light "D" comes
off. Once you close the
door, the wash cycle set
previously will begin.
You want to wash on the
upper rack only?
Remember to use half the
amount of detergent.
Your dishwasher also
allows you to wash half a
load, to save water and
electricity.
Before setting any wash
cycle whatsoever, press
button Q to select that
you want to run a half cycle
on the upper rack.
When you press it, you will
hear a beep and indicator
light R corresponding to
the selected function will
come on.