Filter
Top Products
ARISTON DISHWASHER - User Manual 5
www.aristonappliances.us
You have loaded your dishes and you now have to set
the wash cycle. It takes just one minute to learn how
Starting the dishwasher
You can cancel the
wash cycle in progress,
if it has only just started.
Make sure the wash
cycle has ended before
removing the dishes!
After performing all the
operations described in the
previous paragraphs press
on-off button "A": indicator
light "B" comes on.
Selecting the wash cycle.
To select the wash cycle
press button "P". Each time
you press the button, a
beep will sound and
indicator lights "E" will light
up in sequence: choose the
cycle you deem most
suited to the type of dishes
to be washed (have a look
at the wash cycle table on
page 7). If the appliance
door is shut, press the Start
button "R" and you will hear
a beep; the cycle will start
up within a few seconds.
The dishwasher keeps you
informed.
Your dishwasher is fitted
with indicator lights (G)
which light up to indicate
the cycle phase under way.
prewash,wash,rinsing,
drying. At all times, your
dishwasher tells you which
cycle phase is under way.
Modifying a wash cycle in
progress.
If you have chosen the
wrong cycle, not to worry!
You can modify the wash
cycle in progress, if it has
only just started.
Keep the RESET button
"R" pressed for about 5
seconds: a prolonged beep
will sound, followed by
three short beeps. Indicator
light "G" will turn off and at
this stage, all the settings
will have been cancelled.
You are now free to re-set
the correct wash cycle.
You've left out a dish?
Well, it happens to
everyone. Interrupt the
wash cycle by pressing the
ON-OFF button, insert the
dish you had forgotten and
press the ON-OFF button
again. The cycle will start
up from where you
interrupted it.
Finished?
The end of the wash cycle
is indicated by two short
beeps and the flashing of
the drying phase indicator
light.
The end of the wash cycle
is indicated by two short
beeps and the flashing of
the drying phase indicator
light.
Turn the appliance off by
pressing button "A", thus
cutting off the electricity
supply.
If accessible turn off the
water tap
Wait a few minutes
before unloading the
dishes: they are very hot!
If you wait a little while,
they dry better thanks to
the steam.
Empty the lower rack
first.
There's been a power
failure? Have you opened
the dishwasher door?
The wash cycle stops and
then restarts when the
electricity comes back on
or when you shut the door.
Everything is under
control!
If opening
the door
soon after
the end of
the program, or during
it, stand away from the
Dishwasher, to avoid
possible injury from
hot steam.
You decide when it starts.
When you have loaded the
dishes, you can choose
when to start your
dishwasher before setting
the wash cycle desired.
Press button "D" to delay
the start of the wash cycle
by 12, 9, 6 or 3 hours.
Each time you press it, you
will hear a short beep and
the indicator light "G"
corresponding to the
selected delay will light up.
Now you can select the
desired wash cycle. Press
the start button "R" and
after you hear the beep, the
countdown to the delayed
start will begin.
Once this time is up, the
indicator light will stop
flashing and the wash cycle
will begin.
If you have set a 12 hour
delay, for example, once
you have selected the
wash cycle, the 12 hour
indicator light will flash
followed by the others in
sequence until the set time
delay is up. A quick look at
the indicator lights will keep
you informed of the
countdown progress at all
times.
Have you changed your
mind?
If you change your mind,
you can set a shorter time
delay: press button "D" to
select it. You need not reset
the wash cycle.
If on the other hand you
want to cancel the delay
set and you want the
cycle to start immediately,
press button "D"
repeatedly until the cycle
starts and indicator light
"G" corresponding to the
cycle start phase comes
on.
Dual function of indicator
lights "G"
1) flashing to indicate a
delayed start: to remind
you that you have set a
delayed start;
2) on and not flashing
beneath the cycle phase
symbol:
meaning the cycle has
started and is in the phase
indicated by the symbol.
You want to wash on the
upper rack only?
Remember to use half the
amount of detergent.
Your dishwasher also
allows you to wash half a
load, to save water and
electricity.
Before setting any wash
cycle whatsoever, press
button F to select that
you want to run a half cycle
on the upper rack.
When you press it, you will
hear a beep and indicator
light H corresponding to
the selected function will
come on.
Would you like to see which
settings you have made?
At any time, when the
cycle is under way, if you
press button "P", the cycle
in progress indicator light
will light up for a few
seconds, followed by the
half load indicator light,
wherever set.
Ready, steady, go!