Page 7
Drying
This lets you select how long the turbo fan runs after
the final rinse. You have three options: Short, Economy
or Normal drying. (Note: This option is not available
with the Pots & Pans and Rinse and Hold programs.)
To set the drying time, press Menu until “Drying”
displays, then press Set until your preference displays.
Express
This option reduces the wash time and lowers the wash
temperature by 20° F. (Note: This option is not available
with the Quick Wash, Pots & Pans and Rinse and Hold
programs.) Press Menu until Express displays, then
press Set once to select On or twice to select Off. Press
Menu to confirm your selection.
Super rinse
The Super rinse option adds two extra rinses. This
gives an even better rinsing result. The Super rinse
option can be used in all programs except the Quick
wash and Rinse and Hold programs. Press Menu until
Super rinse displays, then press Set once to select On
or twice to select Off. Press Menu to confirm your
selection.
Cool Touch
This option lets you set a cool-down cycle after the drying
program (in all programs except Rinse and Hold). Press
Menu until Cool Touch displays, then press Set once to
select On or twice to select Off. Press Menu to confirm
your selection.
POWER BUTTONPOWER BUTTON
POWER BUTTONPOWER BUTTON
POWER BUTTON
Use this button to turn the main power to the unit on
and off. The location of the power button is illustrated
on page 6.
STST
STST
ST
ARAR
ARAR
AR
T/STT/ST
T/STT/ST
T/ST
OP BUTTOP BUTT
OP BUTTOP BUTT
OP BUTT
ONON
ONON
ON
Once you have selected the wash program and options,
press this button to start the dishwasher. (Make sure
the door is securely closed.)
FF
FF
F
AA
AA
A
ULUL
ULUL
UL
T CODEST CODES
T CODEST CODES
T CODES
In the event that the machine should fail during a
program, the display window will show a fault code. The
table below defines these codes and gives possible
causes and solutions. See also “Troubleshooting” on
page 13.
Display Type of Fault and Recommended Action
Overfilling Too much water has entered the dishwasher. Call a service technician.
Water Inlet Fault Water inlet fault. Make sure the water supply is open.
Inlet Valve Leakage Valve leakage. Shut off the water supply and contact a service technician.
Water Outlet Fault The drain is blocked. See “Troubleshooting” on page 12.
Blocked Filter The filter is clogged. See “Cleaning the Filters” on page 9.
If you have corrected the fault, turn the main power off
then back on to remove the fault indication. If it still
displays, try again to correct the problem or call a service
technician.
PROGRAM TIMESPROGRAM TIMES
PROGRAM TIMESPROGRAM TIMES
PROGRAM TIMES
The program times may not always be the same
because of variations in the household hot water
temperature. The dishwasher heats the water to the
proper temperature for the program selected; so if the
temperature of the water entering the dishwasher is too
low, the dishwasher will run longer because it takes
longer to heat the water. Raising your water heater
setting could help to shorten the cycle times.
INTERRINTERR
INTERRINTERR
INTERR
UPTING UPTING
UPTING UPTING
UPTING
A PRA PR
A PRA PR
A PR
OGRAMOGRAM
OGRAMOGRAM
OGRAM
TO ADD AN ITEMTO ADD AN ITEM
TO ADD AN ITEMTO ADD AN ITEM
TO ADD AN ITEM
If you want to interrupt a program to add an item, open
the door slightly until the spray arms stop turning. You
can then open the door fully and place the item into the
dishwasher. Close the door securely. The program will
continue from where it was interrupted.
WARNING! Be extremely careful when opening the
door during a program. The water is hot and you
could get scalded.
CHANGING OR STOPPING ACHANGING OR STOPPING A
CHANGING OR STOPPING ACHANGING OR STOPPING A
CHANGING OR STOPPING A
PRPR
PRPR
PR
OGRAMOGRAM
OGRAMOGRAM
OGRAM
If you decide to change the program after you have started
the machine, press the Start/
Stop button for three
seconds. You will have to select the program and options
again when you are ready to restart the program. (Note:
If the program has already gone through the wash cycle,
you will have to add detergent.).