Filter
Top Products
ENGLISH
XENYX 1622FX/1832FX/2222FX/2442FX User Manual
16
ENGLISH
XENYX 1622FX/1832FX/2222FX/2442FX User Manual
17
wired in a balanced conguration. In case of doubt, contact
the microphone manufacturer!
Connect microphones before you switch on the ◊
phantom power supply. Please do not connect
microphones to the mixer (or the stagebox/wallbox)
while the phantom power supply is switched on. In
addition, the monitor/PA loud-speakers should be
muted before you activate the phantom power supply.
After switching on, wait approx. one minute to allow
for system stabilization.
Caution! Please also note the information given in ◊
chapter 6.2.1 “Audio connections”.
SERIAL NUMBER
Please note the important information on the serial number
given in chapter 1.3.3.
INSTALLATION6.
Rack mounting6.1
The packaging of your mixing console contains two 19" rack
mounts for installation on the side panels of the console.
Before you can attach the rack mounts to the mixing
console, you need to remove the screws holding the left
and right side panels. Then, use these screws to fasten the
two rack mounts, each specically to one side. With the
rack mounts installed, you can mount the mixing console
in a commercially available 19" rack. Be sure to allow for
proper air ow around the unit, and do not place the mixing
console close to radiators or power amps, so as to avoid
overheating.
Only use the screws holding the mixing console side ◊
panels to fasten the 19" rack mounts.
Cable connections6.2
You will need a large number of cables for the various
connections of the console. The illustrations below show the
wiring of these cables. Be sure to use only high-grade cables.
Fig. 6.1: Foot switch connector
Audio connections6.2.1
Please use commercial RCA cables to wire the 2-track inputs
and outputs.
You can, of course, also connect unbalanced devices to
the balanced input/outputs. Use either mono plugs, or use
stereo plugs to link the ring and shaft (or pins 1 & 3 in the
case of XLR connectors).
Fig. 6.2: XLR connections
strain relief clamp
sleeve
tip
sleeve
pole 1/ground
tip
pole 2
The footswitch connects both poles momentarily
1/4" TS footswitch connector
input
output
For unbalanced use, pin 1 and pin 3 have to be bridged
1 = ground/shield
2 = hot (+ve)
3 = cold (-ve)
12
3
1
2
3
Balanced use with XLR connectors
Caution! You must never use unbalanced XLR ◊
connectors (PIN 1 and 3 connected) at the MIC input
jacks if you want to use the phantom power supply.
Fig. 6.3: 1/4” mono plug
Fig. 6.4: ¼" stereo plug
Fig. 6.5: Insert send/return stereo plug
Fig. 6.6: Stereo plug for headphones connection
Strain relief clamp
Sleeve
Tip
Sleeve
(ground/shield)
Unbalanced ¼" TS connector
Tip
(signal)
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.
Balanced 1/4" TRS connector
ring
cold (-ve)
tip
hot (+ve)
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
Connect the insert send with the input and the
insert return with the output of the effects device.
Insert send return 1/4" TRS connector
ring
return (in)
tip
send (out)
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
1/4" TRS headphones connector
ring
right signal
tip
left signal