Filter
Top Products
15 16
REVERSING THE DOOR
We recommend that you reverse the door before switching on for the first time.
Tools required: Small and medium size flat and cross-headed screwdrivers, a pair of pliers.
Spare Parts supplied in the plastic bag: The following parts, which are exclusively for left hand side fitted hinge operation
are supplied in a plastic bag with the appliance:
- Door top trim hinge covers – there are 2 different parts, one for each side of top trim.
We suggest you keep all the parts supplied in the plastic bag and also parts, which have been removed when reversing
the door, in a safe place for possible future, re-use.
IMPORTANT: We suggest you ask somebody to help you when moving the appliance around and to hold the door when
removing / re-fitting hinges and the door to avoid any injury and damage to the product.
Please refer to diagrams supplied. To follow numbers in brackets below, refer to the main diagram.
1. Switch off the appliance at the socket outlet and pull out the mains plug.
2. Remove all loose items and fittings and food inside the appliance.
3. Gently prise off plastic hinge covers on both sides of front top panel using a small flat-headed screwdriver.
(1-2)
4- Unscrew the bolts of the top hinge and remove top hinge.
(3)
5- Remove door carefully off the bottom hinge and stand door upright in a safe place.(4)
6. Gently prise off plastic hinge cover on door top trim. Fit the other door top trim plastic off hinge cover supplied in the
plastic bag.(5)
7. Gently tilt the appliance back against a strong wall on its rear side sufficiently to allow the lower hinge to be removed.
Take care to protect the appliance, your wall and floor coverings. You can utilise the original packaging to do this.
Once you tilt the appliance back, check to make sure the appliance is completely stable and safe before you carry
on. (6)
8. Remove the kick plate by pulling it back.(7)
9. Unscrew and remove the adjustable foot bracket if required remove foot.(8)
10. Unscrew and remove the bottom hinge.(9)
11. Unscrew and remove the bottom hinge door stopper and bushing and reposition them on the other side while rotating
the bushing 180°.(10)
12. Unscrew and remove the bottom hinge pin using a pair of pliers and fix it to the hole next to its original position. (11)
13. Fit the bottom hinge to the cabinet as shown in the figure.(12)
14. Fit the adjustable foot bracket as shown in the figure.(13)
15. Reposition the kick plate plastic cover on the other side.(14)
16. Fit the kick plate.(15)
17. Locate and re-fit door to bottom hinge pin.(16)
18.
Rotate the top hinge 180°. Unscrew the hinge pin and re-tighten it to the
opposite side. (17)
19. Re-fit the upper hinge on the opposite side by using a flat headed screwdriver.(18)
20. Fit front top panel plastic hinge covers on the opposite sides.(19)
21. Remove the handle cover gently taking care not to damage the appliance.(20)
22. Unscrew and remove the handle (21). Do not unscrew the yellow coloured screws!
23. Rotate 180 degrees and fit handle to the other side after removing hole plugs gently.(22,23)
24. Fit the handle cover.(24)
25. Adjust the two front feet if necessary.
26. Check that door opens and closes easily, it is aligned correctly and there are no gaps allowing air into the cabinet. If
there are gaps between the door seal and the cabinet, adjust the door seal by gently pulling away from the door using
fingers.
27. Check that all the hinge screws are tightened. Avoid over tightening the screws.
28. Put all items, fittings back in the appliance.
29. Wait for at least 4 hours to allow the system to settle before switching on.
30. Once the correct storage temperatures have been reached in the appliance, put back all the food.
16
13
14
4
2
1
24
23
20
45 °
6
18
19
19
7
8
9
22
(17)
12
15
11
180°
17
21
26
5
3
10
5