Filter
Top Products
INSTRUCTION FOR USE
3
- Avoid contacting moving parts.
- Never unplug from the outlet when your hands are wet or by pulling the
power cord.
- Never carry or pull the appliance by the power cord.
- Do not pull or jam the power cord against sharp edges, do not leave it hanging,
do not run or hang it over hot objects, including the stove or a bare flame.
Protect the power cord against heat or oil.
- Do not let cord hang over edge of table or counter.
- Only use an extension cord if you are sure that it is in perfect condition.
Do not switch the appliance on (immediately unplug from outlet) if:
- the appliance housing or power cord is damaged.
- a defect is suspected after dropping or damaging.
- the parts used are not the original parts.
In this case the appliance must be sent for repair to BODUM
®
or your specialist
dealer.
- Electrical appliances must only be repaired by skilled persons.
- Inadequate repair can create significant hazards to users and is not covered
by the guarantee.
- Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or is dropped or damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair or
electrical or mechanical adjustment.
- BODUM
®
cannot accept any liability for damage if the appliance is
misused, incorrectly operated or inadequately repaired. Under these
circumstances the guarantee will be void.
- The use of attachments not recommended or sold by the manufacturer may
cause fire, electric shock or injury.
- Place the appliance on a flat firm surface. Ensure that it cannot fall into water
and that no water can splash onto electrical parts.
- Never place the appliance close to or in contact with liquids or steam.
- Only clean the appliance when dry using a brush or a damp cloth.
Warning: It is essential to disconnect the mains plug before cleaning.
KEEP THESE INSTRUCTIONS
INITIAL OPERATION
Place the appliance on a level surface. Unreel the required length of cord.
It is important to keep the cord short. Insert the cord into the power cord
inlet provided so that it is clamped and insert the plug into the socket outlet.
Pack the excess cord length in the cord-tidy (fig.10). Open the lid (fig.11) of
the bean container, fill the bean container with the desired quantity of coffee
beans (250g max.) (fig.12) and close the lid (fig.13). The appliance is then ready
to operate.
SETTING THE GRINDING CONTROL
The main adjustment positions stated on the control for the degree of grinding
are normally sufficient. The degree of grinding can be adjusted by twisting the
bean container (fig 14).
= fine grinding (e.g. for espresso coffee machines)
= medium grinding (e.g. for filter coffee machines)
= coarse grinding (e.g. for BODUM
®
French Press
®
coffee maker)
ANTIGUA
4
If the three adjustment positions do not precisely match your personal taste you
can also grind your coffee by choosing any intermediate position.
If the appliance has been filled with coffee beans, the grinding control
must only be operated when the motor is running.
IMPORTANT INSTRUCTIONS
- The BODUM
®
coffee grinder is preset to position (medium grinding).
- Only adjust the grinding control while the motor is running.
- Always keep the lid (fig.1) of the bean container tightly shut in order to
enjoy the full taste and aroma of your coffee beans. Never grind more coffee
than you actually need.
QUANTITY CONTROL
The BODUM
®
coffee grinder is equipped with a time/quantity control (fig.7).
Use it to set the coffee grinder to the desired grinding time and quantity. The
appliance switches off automatically once the preset time has elapsed. If you
want to interrupt grinding before the preset time has elapsed, simply turn the
rotary knob back to the left until the appliance switches off.
The quantity of ground coffee you need to make your coffee depends on the
type of bean, the degree of grinding and your personal taste.
Warning: In order to prevent the motor from overheating, do not grind
more than 2 complete units (2x12 cups) in succession. After wait 10 Min.
to let the motor cool down befor restart.
After each grinded unit (12 cups), empty the coffee container.
This prevents the motor overheating.
STONE SAFETY CUT-OUT FEATURE
Given the huge quantities of coffee that are packed every day, very small stones
may accidentally find their way into even the finest coffee beans. The appliance
is equipped with a stone safety cut-out - or ”friction clutch”- in order to prevent
damage to the grinding gear. A stone in the grinding gear will cause a loud
rattling noise. Switch the appliance off immediately, remove plug from wall outlet,
open it as described in the section entitled "Maintenance" and remove the stone.
MAINTENANCE
Cleaning the grinding gear
Disconnect the mains plug from the socket outlet. Remove any remaining beans
in the bean container (fig.15) and take the latter off by twisting it in an anti-
clockwise direction as far as the release area stop (fig.16). Lift the bean hopper
from the housing (fig.17). The grinding ring can then be lifted out of the
machine.
A soft-bristle brush is ideal for cleaning the grinding gear. Reassemble the
machine by performing the above operation in reverse order. Housing and
transparent parts can be cleaned easily using a damp cloth.