Braun MP81 Juicer User Manual


 
Our products are engineered to meet the highest
standards of quality, functionality and design.
We hope you thoroughly enjoy the new Braun
appliance.
Caution
Read all instructions carefully before using
this product.
This product is suitable for normal household
use only and not for commercial use.
Keep out of children’s reach.
This appliance has a polarized plug (one
blade is wider than the other). To reduce the
risk of electric shock, this plug will fit in a
polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
Do not attempt to defeat this safety feature.
Do not reach into the filling shaft while the
motor is running. Always use the pusher to
guide food through the shaft.
Remove plug from socket before assambling
or disassembling appliance.
Braun electric appliances meet applicable
safety standards. Repairs on electric
appliances must only be done by authorized
service personnel. Faulty, unqualified repair
work may cause accidents or injury to the
user.
The mains cable of this appliance can only
be changed by an official Service dealer, since
it requires a special tool.
Specifications
Voltage/wattage: See typeplate on the bottom
of the appliance.
Safety system: The appliance can only be
switched on when the cover has been fully
locked into position and can only be opened
when the switch has been turned off.
Motor stop: The motor will stop completely
within 2 seconds of switching the appliance
off.
Safety fuse
If the appliance is overloaded the safety fuse will
cut out. To restart the appliance:
Turn the switch off = «0» (important!).
Unlock and remove the cover .
Clean the juice ring , filter and cover .
Allow the appliance to cool down approx.
20 minutes.
Assemble the juicer again.
Turn the switch on = «/».
If the appliance still does not run, allow it to
cool down again.
Description
Motor part
On/off switch
Unlocking buttons
Pulp container
Juice ring
Filter
Cover
Filling shaft
Filling tray
Pusher
Juice spout
Juice container with foam separator
Cord storage
Before using for the first time, wash the juicer
parts (see «Disassembling» and «Cleaning»).
Assembling
1. Put the juice ring on the motor part
(fits loosely without engaging).
2. Lay the filter into the juice ring .
3. Put the cover on and push down firmly with
both hands until your hear it snap into place.
4. Hang the pulp container into the hinges
(the top one first); then close it and be sure it
snaps into place.
5. Put the juice container underneath the juice
spout (A). Capacity: 500 ml/16.9 fl. oz.
The juice container comes with a foam
separator to ensure clear foam-free juice. If it
is not required simply remove it from the juice
container. You can, of course, place a glass
or other container underneath the juice spout
to collect the juice.
6. For easier filling, put the filling tray on top
of the filling shaft (A).
Preparing fruit or vegetables
Im
portant: Use only well ripened fruits, otherwise
the filter may be clogged up which would
result in repeated cleaning of the filter. Wash or
peel the fruit or vegetables you want to process.
Fruit with large pips or stones should always
have these removed first. Process seed fruit
(such as apples, pears) with peels and cores.
Fruit and vegetables with thick peels (e. g. citrus
fruits, melons, kiwis, beets) must be peeled first.
For grapes, cut off the main stem. For leaf
vegetables (e. g. cabbage and spinach) and
herbs, roll up leaves together tightly. Cut fruit and
vegetables into pieces large enough to fit into the
filling shaft.
Currants and rhubarb are not
suitable for making
juice in this juice extractor.
2
7
5 6 7
2
1
2
3
4
5
6
7
8
9
10
11
12
13
5 1
6 5
7
4
12
11
9
8
6
4290365_MP80/81_NA Seite 3 Donnerstag, 31. Januar 2002 12:04 12