Braun M880 Blender User Manual


 
4
English
Our products are engineered to meet the
highest standards of quality, functionality
and design. We hope you thoroughly enjoy
your new Braun appliance.
Caution
Read all instructions carefully before
using this product.
This appliance was constructed to
process normal household quantities.
Please remember to keep your Braun
handmixer out of the reach of children.
Before operating, check whether your
voltage corresponds to the voltage
printed on the top of the unit.
Only with the models M 870, 880 and
M 880 M:
The blade inserts are very sharp!
Do not reach into or underneath the
blades.
Braun electric appliances meet
applicable safety standards.
This appliance can only be opened by
an authorised Braun Service Centre for
repairs.
The cord of this appliance may only be
replaced by an authorised Braun
Service Centre since special tools are
required.
Faulty, unqualified repair work may
cause accidents or injury to the user.
For UK only:
IMPORTANT
Your appliance is already fitted with a plug
incorporating a 3 A fuse. If it does not fit
your socket the plug should be cut off from
the mains lead and an appropriate plug
fitted. Throw away the cut off plug; do not
insert it in a 13 A socket elsewhere in the
house as this could cause a shock hazard.
IMPORTANT – Fitting a Different Plug:
The wires in the mains lead are coloured in
accordance with the following code:
Blue – Neutral Brown – Live
If the colours of the wires in the mains lead
do not correspond with the coloured
markings identifying the terminals in your
plug, proceed as follows:
The blue wire must be connected to the
terminal marked with the letter N or
coloured black. The brown wire must be
connected to the terminal marked with the
letter L or coloured red.
Never connect the blue or brown wire to
the earth pin (E), when using a three pin
plug. The appliance must be protected by
a 3 amp fuse if a 13A (BS 1363) plug is
used.
The fuse cover must be refitted when
changing the fuse. If the fuse cover is lost
do not use the plug until a replacement
cover has been fitted. These parts are
available from authorised Braun Service
Dealers. Never use the plug without the
fuse cover fitted.
Description
All models:
Motor part
Opening for the handblender
attachment
P
%
Cover for the opening

Opening marked with a hexagon
Opening marked with a circle
Ejection key for the dough hooks
/
M
,
the whisks
N
/
O
and the chopper
attachment CA-M
Switch
Locking flap-up spout for winding up the
cord around the motor part (g)
Anti-skid base ring
Dough hook with hexagonal plate
M
Dough hook with round plate
N
Whisk with round plate
O
Whisk with hexagonal plate
With the models M 820, M 830, M 870,
M 880 and M 880 M only:
P
Handblender attachment
Q
Mark for maximum immersion of the
handblender attachment
P
With the models M 830, M 880
and M 880 M only:
R
Mixing/measuring beaker with air-tight
lid (to be used only with the hand-
blender attachment
P
)
With the models M 810, M 830, M 880
and M 880 M only:
S
Wall holder
With the models M 870, M 880
and M 880 M only:
Chopper attachment CA-M
T
-
W
T
Upper part
U
Blade insert
V
Chopper bowl with modell indenti-
fication on the bowl (CA)
W
Anti-skid double function base/lid
Notice: All models can be extended b
y the
handblender attachment
P
and the
chopper attachment CA-M
T
-
W
and
HC-M (without illustration), if these
attachments are not standard with your
model.
Specifications
Voltage/wattage: see type plate on the
motor part
.
Automatic shut-off
If the appliance is overloaded, e. g. if the
motor is blocked, the motor part may be
automatically switched off.
If this is the case, light vibrations may be
observed. The inserts stop rotating or
rotate only very slowly. Turn the switch off,
so that the motor can cool off. After a
cooling off period of at least 10 minutes it
can be switched on again.
Switch
Switch
position:
P = «pulse» (speed corresponds
to setting «3»
0 = Off
1 = Low speed
2 = Medium speed
3 = High speed
Assembling/disassembling
Important
: Always set the switch to
position «0» and plug the appliance before
assembling or disassembling the
appliance, in order to avoid accientally
switching on the appliance when inserting
the two dough hooks or two whisks.
For inserting the dough hooks and whisks
correctly, see illustrations (a) and (b).
Once inserted, the dough hooks or whisks
can only be ejected by pressing the
ejection key (c). However, for safety
reasons this is only possible when the
handmixer is switched off.
How to use the handmixer
Dough hooks
/
M
For kneading yeast dough, pasta dough,
pastries, as well as for mixing heavy
minced meat doughs.
Generally all speed settings may be used.
The speed settings are recommended as
follows:
Switch
position 1:
Mixing of e. g. nuts and fruits into
heavy doughs.
Switch
position 2:
Kneading of the dough ball and working
in of ingredients.
Switch
position 3:
Fast mixing of all ingredients.
5