Filter
Top Products
Softener adjustment
The efficiency of your dishwasher depends on the softness of the tap water. To ensure best efficiency, the dishwasher
is equipped with a system that reduces the hardness in the mains water supply. The efficiency will increase when the
system is correctly set. To find out the water hardness level of your water supply you can use the test strip supplied or
alternatively contact your local water board.
1. Open the testing strip.
2. Run water through the tap for one minute.
3. Hold the testing strip in water for one second.
4. Shake the testing strip after taking it out of the water
5. Wait for one minute
6. Check the number of marks on the strip to see the level of water hardness.
If the hardness of the water you use is above 60 dE or if you are using well water; you are recommended to use lter and
water refinement devices.
Please note: The level of water hardness is preset to level 3.
1. Press and hold down the programme selection button
2. Press the power button to switch on the dishwasher
3. Keep the programme selection button pressed until the five programme indicator lights and the end of programme
indicator light flash.
4. To adjust the level, press the programme selection button until the required level is selected. The programme lights
will illuminate as in the table of water hardness settings.
5. To store the selected water hardness level, press the power button.
Testing strip
Adjusting salt consumption
Table of Water Hardness Level Settings
NOTE:
The washing effectiveness of your machine depends on the softness of the tap water. For this
reason, your machine is equipped with a system that reduces the hardness in mains water
supply. The washing effectiveness will increase when the system is correctly set. To find out
the water hardness level of water in your area, contact your local water board or determine
water hardness level by using the test strip(if available).
If the hardness of the water you use is above 90 dF (French hardness) or if you are using well
water; you are recommended to use filter and water refinement devices.
Hardness level is adjusted to level 3 as a factory setting.
9
ENGLISH
Open the
testing
strip.
Run
water
through
your tap
for 1
min.
Keep the
testing
strip in
water for 1
sec.
Shake the
testing strip
after taking it
out of water.
Wait for
1 min.
Make your machine’s water hardness
setting according to the result
obtained through the testing strip.
No Lime
Very low lime content
Low lime content
Medium lime content
Lime content
High Lime content
If the hardness of the water you use is above 63dE or if you are using well water; you are recommended to use filter and
water refinement devices.
Softener adjustment
The efficiency of your dishwasher depends on the softness of the tap water. To ensure best efficiency, the dishwasher
is equipped with a system that reduces the hardness in the mains water supply. The efficiency will increase when the
system is correctly set. To find out the water hardness level of your water supply you can use the test strip supplied or
alternatively contact your local water board.
1. Open the testing strip.
2. Run water through the tap for one minute.
3. Hold the testing strip in water for one second.
4. Shake the testing strip after taking it out of the water
5. Wait for one minute
6. Check the number of marks on the strip to see the level of water hardness.
If the hardness of the water you use is above 60 dE or if you are using well water; you are recommended to use lter and
water refinement devices.
Please note: The level of water hardness is preset to level 3.
1. Press and hold down the programme selection button
2. Press the power button to switch on the dishwasher
3. Keep the programme selection button pressed until the five programme indicator lights and the end of programme
indicator light flash.
4. To adjust the level, press the programme selection button until the required level is selected. The programme lights
will illuminate as in the table of water hardness settings.
5. To store the selected water hardness level, press the power button.
Testing strip
Adjusting salt consumption
Table of Water Hardness Level Settings
NOTE:
The washing effectiveness of your machine depends on the softness of the tap water. For this
reason, your machine is equipped with a system that reduces the hardness in mains water
supply. The washing effectiveness will increase when the system is correctly set. To find out
the water hardness level of water in your area, contact your local water board or determine
water hardness level by using the test strip(if available).
If the hardness of the water you use is above 90 dF (French hardness) or if you are using well
water; you are recommended to use filter and water refinement devices.
Hardness level is adjusted to level 3 as a factory setting.
9
ENGLISH
Open the
testing
strip.
Run
water
through
your tap
for 1
min.
Keep the
testing
strip in
water for 1
sec.
Shake the
testing strip
after taking it
out of water.
Wait for
1 min.
Make your machine’s water hardness
setting according to the result
obtained through the testing strip.
No Lime
Very low lime content
Low lime content
Medium lime content
Lime content
High Lime content
Wash light is on
Rinse light is on
Dry light is on
End light is on
Wash and End lights are on
Rinse and End lights are on
To adjust the water softener level
1. Turn the programme selection dial to zero (reset) when the dishwasher is switched off.
2. Press and hold in the start/pause button.
3. Whilst holding in the start/pause button, switch on the dishwasher using the power on/off button.
4. Release the start/pause button once the indicator lights have flashed.
The indicators will show the last selected water hardness setting.
5. To adjust to the level required, press the start/pause button until the indicators show the correct level.
6. To save the set level, press the on/off button again.