CFM GEF30 Ventilation Hood User Manual


  Open as PDF
of 2
 
USA
www.continentalfan.com
Canada
www.aeroflo.com
CCoonnttiinneennttaall FFaann MMaannuuffaaccttuurriinngg IInncc..
203 Eggert Rd.
Buffalo, NY 14215
Tel: 716-842-0670 Toll: 800-779-4021 Fax: 716-842-0611
AAeerroofflloo IInncc..
12-205 Matheson Blvd. East
Mississauga, ON L4Z 3E3
Tel: 905-890-6192 Toll: 800-779-4021 Fax: 905-890-6193
IINNSSTTAALLLLAATTIIOONN PPRROOCCEEDDUURREE
MMOODDEELLSS SSEEFF--1100 TTHHRROOUUGGHH SSEEFF--3300
When shutter is mounted to fan assembly:
1. Cut square wall opening size ½” larger than fan blade
diameter.
2. From inside of building / room, center fan assembly over
wall opening. Fan must be positioned so that junction box
is located at bottom and shutter is level and square, with
shutter blades opening upwards.
3. Lag fan to wall through mounting holes in shutter gusset,
using appropriate fasteners (by others).
4. Rotate fan impeller by hand, ensuring that it is unobstructed
and rotates freely.
5. Make electrical connections to fan junction box.
When shutter and fan assembly are mounted separately:
1. Cut wall opening size ½” larger than fan blade diameter.
2. From inside of building / room, center fan assembly over
wall opening. Fan must be positioned so that junction box
is located at bottom.
3. Lag fan to wall through wire hooks on guard, using the
appropriate fasteners (by others).
4. Apply caulking compound (by others) to rear of shutter
gusset.
5. From outside of building / room, center shutter over wall
opening, ensuring that shutter is level and square, with
shutter blades opening upwards.
6. Lag shutter to wall through mounting holes in shutter gusset,
using appropriate fasteners (by others).
7. Rotate fan impeller by hand, ensuring that it is unobstructed
and rotates freely.
8. Make electrical connections to fan junction box.
MMOODDEELL PPEEFF--1100 TTHHRROOUUGGHH PPEEFF--3300
1. Cut wall opening size ½” larger than fan venturi opening.
2. From inside of building / room, center fan panel assembly
over wall opening. Fan must be positioned so that
junction box is located at bottom.
3. Lag fan to wall through mounting holes in panel, using
appropriate fasteners (by others).
4. Rotate fan impeller by hand, ensuring that it is unobstructed
and rotates freely.
5. Make electrical connections to fan junction box.
MMOODDEELLSS GGE
EFF--1100 TTHHRROOUUGGHH GGEEFF--3300
1. Cut wall opening size ½” larger than fan blade diameter.
2. From inside of building / room, center fan assembly over
wall opening. Fan must be positioned so that junction box
is located at bottom.
3. Lag fan to wall through wire hooks on fan guard, using the
appropriate fasteners (by others).
4. Rotate fan impeller by hand, ensuring that it is unobstructed
and rotates freely.
5. Make electrical connections to fan junction box.
RREECCOOMMMMEENNDDEEDD MMAAIINNTTEENNAANNCCEE
1. When undertaking maintenance or service work, ensure
that electrical service to fan is locked in the “OFF” position
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked,
securely fasten a prominent warning device such as a tag
to service panel.
2. Do not re-establish power supply until maintenance or
service work has been completed.
3. Maintenance or service work must be performed by a qual-
ified person in accordance with all applicable codes and
standards, including local fire codes.
4. Motor bearings are factory lubricated and do not require
additional lubrication.
5. Remove airborne contaminants that have settled on motor
using an air hose or vacuum.
6. Clean fan blades, guard or shutter using a mild detergent.
Do not allow cleanser to come in contact with fan motor or
electrical parts.
LLIIMMIITTEEDD WWAARRRRAANNTTYY
This equipment is warranted to be free from defects in material
and workmanship for a period of one (1) year from date of
purchase. Any units or parts which prove to be defective
during warranty period will be repaired or replaced at
Vendor’s option. Vendor is not responsible for any removal,
installation or transportation costs.
Motors are warranted separately by motor manufacturer for
a period of one (1) year, and should be returned to nearest
authorized motor service center for repair.
All warranty claims must be processed through point of purchase.
WWIIRRIINNGG PPRROOCCEEDDUURREE
SEF-PEF-GEF I&M-0710
 previous