Cres Cor CO-151-FUA-12B Convection Oven User Manual


  Open as PDF
of 2
 
5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: 440/350-7267
www.crescor.com
© Crescent Metal Products, Inc. 1998 All rights reserved.
Litho in U.S.A.
®
CO-151-FUA-12B
In line with its policy to continually improve its products,
CRES COR reserves the right to change materials and
specifications without notice.
SHORT FORM SPECIFICATIONS
Cres Cor Roast-N-Hold Convection Oven Model
CO-151-FUA-12B. Removable power unit 20 ga. 304
stainless steel, recessed control panel. Cabinet and Dutch
doors 22 ga. 304 stainless steel; stainless steel internal
frame; coved corner interior. Fiberglass insulation in sides
2”; back, doors and base 1-1/2”. High temperature magnetic
latches. (12) sets universal angles for multiple pan sizes and
spacing. One piece base .125 aluminum. 5" swivel modulus
casters, Delrin bearings. Load capacity 250 lbs. each.
8200 Watts,
Volts, 60 Hz., Phase. 2 year
parts warranty. Provide the following accessories:
___ ___ ___UL Sanitation, UL, CUL listed.
CRES COR PAN DIM “A” DIM “B” DIM “C” INSIDE DIMENSIONS WEIGHT
MODEL NO.
CAP/ANGLES
SIZE WIDTH DEPTH HEIGHT WIDTH DEPTH HEIGHT ACT.
12 SEE NOTE IN 28-3/4 37-3/4 73-1/2 21-1/4 26-1/2 58 LBS 378
CO-151-FUA-12B
SETS BELOW MM 740 960 1870 540 675 1475 KG 171
NOTE: Refer to pan size chart at end of section.
ALL CONSTRUCTION IS RIVETED, WELDED AND FINISHED.
CABINET:
• Body: 22 ga. 304 stainless steel.
• Reinforcement: Internal framework of 16 ga. stainless steel.
• Insulation: Fiberglass, thermal conductivity (K factor) is .23
• at 75˚F. 1-1/2" in back wall, doors, base; 2" in side walls.
• Air tunnel: 20 ga. stainless steel, lift-out type, mounted
• on rear wall.
• Push/pull handles (2): 7" vertical; recessed.
BASE:
• One piece construction, .125 aluminum.
• Casters: 5" dia., swivel, modulus tires, 1-1/4 wide, load cap.
• 250 lbs. each, temp. range -45˚/+180˚F. Delrin bearings. Front
casters equipped with brakes.
DUTCH DOORS:
• Field reversible.
• Formed 22 ga. 304 stainless steel.
• Latches: Chrome plated steel, high temperature ceramic
• magnetic type; mounted inboard.
• Hinges: Heavy duty chrome plated steel, lift-off type; mounted
• inboard.
• Gaskets: Perimeter type, silicone.
• Pan stops: Embossed.
PAN SLIDES:
• Wire angles (.306 dia.), nickel chrome plated steel;
•
mounted on lift-out posts.
• 12 sets of angles adjustable on 1-1/2" centers.
• Grids (6): Nickel chrome plated steel, raised wire 17" x 25".
POWER REQUIREMENTS AVAILABLE:
• 8200 Watts, 208 Volts, 60 Hz., 1 phase, 39 Amps.,
•
50 Amp. service.
• 8200 Watts, 240 Volts, 60 Hz., 1 phase, 34 Amps.,
•
50 Amp. service.
• 8200 Watts, 208 Volts, 60 Hz., 3 phase, 23 Amps.,
•
30 Amp. service.
• 8200 Watts, 240 Volts, 60 Hz., 3 phase, 20 Amps.,
•
30 Amp. service.
POWER UNIT COMPONENTS: (refer to above drawing)
• Body: Formed 20 ga. 304 stainless steel with black control
• panel, recessed and tilted 7˚.
A) Thermostat (holding): Solid state, room ambient to 250˚F. (121˚C.).
B) Thermostat (cook/retherm): Solid state, room ambient to 350˚F.
(176.5˚C.).
C) Pilot lights (2).
D) Switch: Lighted ON-OFF rocker type.
E) Timer: 24 hr. digital countdown; infinite memory retention.
F) Thermometer.
• Power cord: Permanent, 6 ft., 6/3 ga. with right angle plug.
• Heaters (3): 2670 Watts each.
• Blower motors (3).
• Vent fans (2).
• Fuses (2): 3 Amp.
INSTALLATION REQUIREMENTS:
• Check local vent hood codes for mobile Roast-N-Hold ovens.
DETAIL OF
PAN SLIDE
 previous