Filter
Top Products
7
To operate the dishwasher;
1. Attach the quick connect hose assembly to the
faucet.
2. Push the door release button to open the door.
3. Check to make sure the filter is securely in its
position.
4. Place dishes on the dish-rack and cutlery inside the
cutlery basket.
5. Check to make sure the spray-arm can rotate freely
by gently spinning it clockwise.
6. Fill the detergent fossa, located in the recessed
area on the inner door panel (up to 12 grams).
NOTE: If using the Pre-wash cycle only, it is not
necessary to add any detergent.
7. Firmly close the door.
8. Open the hot water line.
9. Push the power on/off button inward.
Power button pushed in = on
Power button pushed out = off
The LED indicator (located just above the power
button) will illuminate, thus confirming that the dish-
washer is receiving power.
10.Press the program button until the desired
program code appears in the display window.
The program codes are:
P1, for Intensive wash
P2, for Normal wash
P3, for Rapid wash
P4, for Eco wash
P5, for Pre-wash
11.Press the Start/Reset button to begin the selected
washing program. The display window will flash the
program code throughout the cycle. At the end of the
cycle the dishwasher will stop; the LED will stop
flashing the program code, and the dishwasher will
sound a beep. After ten minutes, the display window
will stop displaying the program code and become
blank (black). The power indicator light remains on
unless the power is turned off (the power on/off
button is pushed out).You can select another
program during operation by pressing the
Start/Reset button, then pressing the program key
(until the desired program code appears in the
display window), and finally by pressing the
Start/Reset button again to confirm program choice.
The dishwasher will restart and begin the selected
wash operation.
Note: For safety reasons, the dishwasher is designed to
stop in the event that the door is opened during a wash
cycle.
IMPORTANT: Once washing is complete, press the
door open button and leave the dishwasher for about
fifteen minutes. This allows the dishes to cool off, as
they may be too hot to touch immediately after washing.
12. After unloading the dishwasher, remove the metallic
filter screen (located on the bottom of the dishwash-
er tub), and wash off any bits of food that may be
caught in it, then return the filter to its proper
position.
NOTE: At the beginning of each cycle the dishwasher
starts in drain mode. This is because the drain pump
always retains a small amount of water (in the sump)
from the previous (last) cycle. This is necessary to keep
the pump primed; therefore, do not be alarmed if you
see a small amount of water being pumped-out from
the drain hose prior to the start of a regular wash cycle.
(This is normal).
Intensive wash (P1)
Water Temperature: Wash 54ºC (129.2ºF) /
Rinse 69ºC (156.2ºF)
Program Duration: 125 minutes
Water Consumption: 10.4 L (22 pts)
Normal wash (P2)
Water Temperature: Wash 52ºC (125.6ºF) /
Rinse 67ºC (152.6ºF)
Program Duration: 130 minutes
Water Consumption: 10.4 L (22 pts)
Rapid wash (P3)
Water Temperature: Wash 49ºC (120.2ºF) /
Rinse 55ºC (131ºF)
Program Duration: 70 minutes
Water Consumption: 9.6 L (20.3 pts)
Economy wash (P4)
Water Temperature: Wash 54ºC (129.2ºF) /
Rinse 69ºC (156.2ºF)
Program Duration: 120 minutes
Water Consumption: 10.4 L (22 pts)
Pre-Wash (P5)
Water Temperature: Incoming water
(tank temperature)
Program Duration: 12 minutes
Water Consumption: 5.4 L (11.4 pts)
Note: Washing time may vary depending on incoming
water temperature and the relevant environmental
temperature.
Operating Instructions
Program Summary/Selection