Filter
Top Products
Project __________________________________
Item ____________________________________
Quantity ________________________________
CSI Section 11400
Approved _______________________________
Date ____________________________________
980 S. Isabella Rd.
Mt. Pleasant, Michigan 48858
Phone: 800-733-8948 or 989-773-7981
Fax: 800-669-0619
www.delfield.com
Exterior top is one-piece, 16-gauge stainless steel, with
integral 2.12” (5.4cm) high square nosing on front. Top has
a mechanically cooled refrigerated raised rail at rear with
openings to accommodate 1/6 size pans. Pans and adapter
bars are provided by others. Pans are recessed 2” (5.1cm). Rail
interior is 22-gauge stainless steel. Raised rail openings have
18-gauge stainless steel removable lids. Unit is equipped with
separate expansion valve and on/off switch for refrigerated
cold pan. Temperature in top opening to maintain 33°F (1°C) to
41°F (5°C) with pans recessed 2” (5.1cm) at 86° ambient room
temperature, meeting NSF7 requirements.
Exterior Back and Bottom are 24-gauge galvanized steel.
Exterior ends are finished with 18-gauge galvanized steel.
Base Interior has 22-gauge stainless steel back and bottom.
Base interior ends and door frames are thermoformed ABS
plastic. Base is insulated with 1.5” (3.8cm) high density
foamed in place environmentally friendly, Kyoto Protocol
Compliant, Non ODP (Ozone Depletion Potential), Non GWP
(Global Warming Potential) polyurethane. End of base has a
machine compartment, standard on right, with condensing
unit installed.
Door(s) have a 22-gauge stainless steel exterior front, with
thermoformed ABS plastic interior liner, black recessed handle
and snap in magnetic gasket which is easily replaceable. Each
interior door section has (1) removable epoxy coated wire
shelf.
Refrigeration System uses HFC-404A refrigerant. Cabinet has
a blower coil assembly with expansion valve located behind
door mullion. Base is equipped with independently controlled
thermostat, solenoid valve and condensate evaporator. On/off
switch for unit is located on panel above louver. Refrigeration
system in the base will maintain 36°F (2°C) to 40°F (4°C).
Legs: Unit is mounted on 6.13” (15.6cm) high adjustable
stainless steel legs.
Electrical connections are 115 volt, 60 Hertz, single phase.
Unit is wired with 8’ (2.4m) cord and plug.
Specifications
Standard Features
Options &
Accessories
16 gauge stainless steel top
High density environmentally
friendly, Kyoto Protocol Compliant,
Non ODP (Ozone Depletion
Potential), Non GWP (Global
Warming Potential) polyurethane
foam insulation throughout unit
Snap-in dart style vinyl magnetic
gasket
Recessed black plastic handle held
in with a positive lock system
14 gauge leg rails that run the
entire length of the unit
6.12” adjustable full stainless steel
legs and bullet feet
8’ cord and plug
36” standard work height
Environmentally friendly HFC-404A
refrigerant
One year parts and 90 day labor
standard warranty
•
•
•
•
•
•
•
•
•
•
F18RC52 52” reduced height raised rail self-contained prep table
F18RC60 60” reduced height raised rail self-contained prep table
F18RC68 68” reduced height raised rail self-contained prep table
F18RC82 82” reduced height raised rail self-contained prep table
F18RC91 91” reduced height raised rail self-contained prep table
F18RC99 99” reduced height raised rail self-contained prep table
•
•
•
•
•
•
Models
F18RC
Reduced Height Raised Rail Self-Contained Prep Table
F18RC: Reduced Height Raised Rail Self-Contained Prep Table
Stainless steel end
Stainless steel back
Laminate facing (full front)
Laminate end
Laminate back
Cutting board (Sanalite or
composite)
Tray rack
Casters
Drawers, (2 or 3 high) 19”, 27” or
32” drawers in lieu of one door
Locks
Cold pan drain
220V/50 cycle
•
•
•
•
•
•
•
•
•
•
•
•
F18RC60
(Shown will optional stainless steel finished end.)