Filter
Top Products
14
Making drinks with milk automatically
The CAPPUCCINO, LATTE, FLAT WHITE and HOT MILK buttons
on the control panel enable these drinks to be prepared
automatically.
Proceed as follows:
1. Fill the milk container and attach it as described above.
2. Turn the froth adjustment dial on the milk container lid to
the position corresponding to the required froth.
3. Press the button corresponding to the required drink. The
name of the drink selected is displayed together with a
progress bar which gradually lls as preparation progres-
ses.
4. After a few seconds, frothed milk is delivered from the
milk spout into the cup below. For drinks with coee, the
machine automatically makes the coee after delivering
the milk.
Please note!
t *GEVSJOHEFMJWFSZZPVXBOUUPTUPQQSFQBSBUJPOQSFTTUIF
corresponding button.
t "UUIFFOEPGEFMJWFSZUPJODSFBTFUIFRVBOUJUZPGNJMLPS
coee in the cup, just press (within 3 seconds) the button
corresponding to the drink being made.
t %P OPUMFBWF UIFNJML DPOUBJOFSPVU PGUIF SFGSJHFSBUPS
for long periods. The warmer the milk (5°C is ideal), the
poorer the quality of froth produced.
Cleaning the milk frother with the CLEAN button
“Press CLEAN “ ashes on the display each time you use a milk
function.
To eliminate all milk residues, proceed as follows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Press the CLEAN button (g. 23) and keep pressing until
the progress bar which appears on the display together
with the message “Cleaning underway” is complete.
Please note!
t *GZPVBSFNBLJOHBOVNCFSPGNJMLCBTFEESJOLTPOFBGUFS
the other, you do not need to clean by pressing the CLEAN
button each time you make a cappuccino.
Just press it once after making the last cup (the appliance
continues functioning even if the CLEAN button is not
pressed).
Important!
After use, always clean the hot water/steam nozzle and the
milk container as described on page 14.
Programming the quantity of coee and milk in the
cup for the CAPPUCCINO, LATTE, FLAT WHITE
and HOT
MILK buttons.
The appliance is set by default to automatically deliver standard
quantities.
To change these quantities, proceed as follows:
1. Place a cup under the coee and milk spouts.
2. Press and hold one of the function buttons until the
message “Milk for … Program Quantity” is displayed.
3. Release the button.
The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the button again.
5. The appliance stops delivering milk and (if required for
the drink being prepared) after a few seconds the coee is
delivered into the cup. “Coee for … Program Quantity”
is displayed.
6. Once the required quantity of coee has been delivered
into the cup, press the button.
Coee delivery stops.
The machine is now reprogrammed with the new quantities
of milk and coee.
DELIVERING HOT WATER AND STEAM
Important! Danger of burns.
Never leave the machine unsupervised while delivering hot
water or steam.
The spout becomes hot during delivery. Hold by the handle
only.
Please note!
If “Energy Saving” mode is enabled, you may have to wait a few
seconds before the hot water or steam is delivered.
Delivering hot water
1. Make sure the hot water spout is attached correctly (g.
6).
2. Place a container under the spout (as close as possible to
avoid splashes).
3. Press the
button (g. 3).
“Hot water” is displayed, together with a progress bar
which lls gradually as preparation proceeds.
4. The machine delivers 250 ml of hot water, then delivery
stops automatically.
To interrupt delivery of hot water manually, press the
button again.
Change the quantity of water delivered automatically.
The machine is set by default to automatically delivery 250 ml
of hot water.