Filter
Top Products
Electric
Water
Warewashing
66″ Single Tank Conveyor Dishwasher
without Built In Hot Water Booster WT66
Inlet Water supply pressure: 22 – 102 psi (150 – 700 kPa)
Inlet Cold Water Supply Temperature
for Pre Wash Tank: 39-59 °F (4-15 °C)
Inlet Water Supply Temperature
Rinse circuit: 194 °F (90 °C)
Wash tank: 80 – 140 °F (27 – 60 °C)
Inlet Water supply hardness: 4 – 8 gpg (7-14 °fH) max
Incoming Cold Water line size
Pre wash: G 3/4″
Incoming Hot Water line size
Wash tank: G 3/4″
Rinse circuit: G 3/4″
Drain line size
Pre wash section: G 1-1/2″
Wash/rinse section: G 1-1/2″
Water consumption: Gallons/hr: 83.2 gal/hr (315 liters)
Water consumption/rack: 0.4 gal/rack (1.5 l/rack)
Pre wash temperature: < 105 °F (<40 °C)
Pre wash tank size: 11.8 gal (45 liters)
Pre wash pump power: 0.5 hp (0,37 kW)
Pre wash pump water flow: 39 gal/min (150 l/min)
Wash temperature: 160 – 172 °F (71-78 °C)
Wash tank size: 26 gal (100 liters)
Wash pump power: 2 hp (1.5kW)
Wash pump flow rate: 118.9 gal/min (450 l/min)
Rinse temperature: 180 – 194 °F (82-90 °C)
Rinse pump power: 0.4 hp (0.32 kW)
Rinse pump water flow: 1.32 gal/min (5 l/min)
Initial fill Hot Water requirements:
26 gal (100 liters)
Initial fill Cold Water requirements: 11.8 gal (45 liters)
Supply voltage: 534094 (WT66CL208) 208 V/3p/60Hz
534095 (WT66CR208) 208 V/3p/60Hz
534096 (WT66CL240) 240 V/3p/60Hz
534097 (WT66CR240) 240 V/3p/60Hz
Machine requires one electrical connection.
Max. Current absorbed: 208 V/3p/60Hz 64A (21 kW)
240 V/3p/60Hz 57.5A (21 kW)
Exhaust Requirements
Unit supplied as standard with extended vent hoods
(can be removed during installation if not required).
Exhaust extraction not more than
177 CFM (300 m³/h)
Refer to installation diagram for minimum exhaust hood
installation height .
Key Information
Productivity racks per hour 200 racks / 3600 dishes
(max speed): (average 18 dishes per rack)
Productivity racks per hour 130 racks / 2340 dishes
(min speed): (average 18 dishes per rack)
Table to Table connection: 66″ (
1676 mm)
Number of Tanks: 1
Height with door open: 83-7/16″ (2119 mm)
Charging hole size (width): 20-7/8″ (530 mm)
Charging hole size (height): 19-3/4″ (501 mm)
Net weight: 1012 lb (459 kg)
Shipping weight: 1210 lb (549 kg)
Shipping width: 74-7/16″ (1890 mm)
Shipping depth: 40-15/16″ (1040 mm)
Shipping height: 81-1/8″ (2060 mm)
Shipping volume: 143 cu.ft (4.05 m
3
)
Noise level: <70 dBA
Unit predisposed to accept external detergent dispensers, detergent
probes and rinse aid dispensers.