Filter
Top Products
Counter-Depth Refrigerator
E23CS78HSS designer series
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
USA
•
250 Bobby Jones Expressway
•
Augusta, GA 30907
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
E23CS78HSS 03/08 © 2008 Electrolux Home Products, Inc. Printed in the U.S.A.
Counter-Depth Refrigerator Specifications
•
Product Weight – 300 Lbs.
•
Voltage Rating –120V/60 Hz/15 or 20 Amps
•
Connected Load (kW Rating) @120 Volts = 1.02kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @120 Volts = 8.5 Amps
•
Always consult local and/or national electric & plumbing codes.
•
When installing next to wall allow 3-1/2" handle clearance.
•
If optional Collar Kit (ECK23CDS) is to be used, refer to Collar Kit
specifications on this page for different cutout dimensions.
•
If optional Louvered Trim Kit (4480) is to be used, refer to Louvered
Trim Kit (4480) Installation Specifications page on web for different
cutout dimensions.
Standard “Built-In Look” Specifications
•
Minimum opening of 70-1/4"H x 36"W x 24"D required for standard
“Built-In Look.” (70-1/4" H to be measured from finished floor to
underside of soffit or overhead cabinet.)
•
Remove all wall/floor molding prior to installation.
•
Water recess on rear wall recommended to prevent water line damage.
Minimum recommended size tubing is 48" x 1/4".
•
Front rollers are adjustable for “Built-In Look.”
Optional Collar Kit (ECK23CDS) Specifications
•
To use optional Collar Kit, an enclosure is required around refrigerator
having a minimum opening of 70-1/4"H x 36-1/8"W x 24-1/2"D with
1/2" minimum side panels.
•
Add maximum of 1/4" to 70-1/4" opening height when installed with
frameless-style overhead cabinets, for door opening clearance.
•
The cabinet or soffit above refrigerator must extend out to same depth
as side panels.
•
To provide additional clearance for overhead cabinet doors when in open
position, allow 1" from underside of cabinet to bottom of cabinet door.
•
A minimum width of 36-1/8" is required for refrigerator installation with
an additional 1/2" or 3/4" added for each side panel.
•
If 1/2" side panels are used, then side trim piece and panel will be
even. If 3/4" side panels are used, then 1/4" of side panel will extend
beyond collar trim and must be finished.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
Optional Accessories
•
Collar Kit – (ECK23CDS).
•
Louvered Trim Kit – (4480).
A
B
C
Cutout
Dimensions
Standard
“Built-In Look”
(A) 70
1
/4"
(B) 36"
(C) 24"
With Collar Kit
(ECK23CDS)
(A) 70
1
/4"
(B) 36
1
/8"
(C) 24
1
/2"
Standard
Refrigerator Depth
vs. Counter Depth
23
5
/8"
Counter Depth
28
1
/2"
Standard Depth
Collar Kit -
Top Trim Piece
Overhead
Cabinet Door
1" min.
Clearance
Refrigerator Case
Cabinet Underside
Top Trim Piece
Magnetic Tape
3
/4" Cabinet
Side Panel
1
/2" Cabinet
Side Panel
Side trim must be installed flush
with the gasket contact surface
on the refrigerator case.
Refrigerator Case
Door Gasket
Collar Kit -
Side Trim Piece
Side Trim Piece
24"
Cabinet
24
1
/2" Side Panel,
1
/2" min. width
(with Collar Kit trim)
24" Side Panel,
1
/2" min. width
(without Collar Kit trim)
25"
Countertop
7
/8" Airspace
(
5
/8" gap +
1
/4" wall plates)
Recessed water line Recessed electrical outlet
Collar Kit - Side Trim Pieces
26
7
/8"
23
5
/8"
35
5
/8"
68
3
/16"
with
3
/8"
rollers
69
5
/16"
Allow at least 45
1
/4" with
doors in 90° open position
29
3
/8" to handle
extension
7
5
/8"
Power
cord
location
(right
bottom
rear)
Water
line inlet
location
(left
bottom
rear)