Filter
Top Products
High-Speed Oven
E30SO75ESS designer series
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA
•
250 Bobby Jones Expressway
•
Augusta, GA 30907
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
E30SO75ESS 01/09 © 2009 Electrolux Home Products, Inc. Printed in the U.S.A.
30" High-Speed Oven Specifications
•
Product Weight – 115 Lbs.
•
Voltage Rating –240V/ 60Hz/15 or 20 Amps
•
Single phase 3- or 4-wire cable, 240 Volt, 60 Hertz AC only electrical
supply with ground required on separate circuit fused on both sides
of line.
•
Connected Load (kW Rating) @ 240 Volts = 3.3kW
•
Amps @ 240 Volts =13.2 Amps
•
Oven has a 6-15 plug, requiring a 6-15 receptacle.
•
Always consult local and/or national electric codes.
•
Allow at least 12" clearance for oven door depth when open.
•
Minimum 22-3/4" deep cutout dimension is critical for proper installation,
to ensure that oven’s faceplate will fit flush against cabinet front.
•
Full oven base of solid plywood or similar material required, capable of
supporting 150 Lbs.
•
Grounded outletshould NOT be located in shaded area, as indicated.
•
Base must be level and cabinet front must be square.
•
High-Speed Oven is NOT approved to be used under counter.
•
High-Speed Oven can be built in alone or is approved to be used in
combination with any Electrolux ICON
®
Single Wall Oven and/or Warmer
Drawer. (Refer to model-specific Combination Installation Specifications
pages on web.)
•
When used in combination with another Electrolux ICON
®
built-in product,
a minimum clearance of 2-5/8" required from bottom of
High-Speed Oven cutout to top edge of companion product’s faceplate,
leaving a 2" visible gap between both product faceplates.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
**When used in combination with another
Electrolux ICON
®
built-in product, a minimum
clearance of 2
5
/8" required from bottom of
High-Speed Oven cutout to top edge of
companion product’s faceplate, leaving a 2"
visible gap between both product faceplates
240V/60Hz
grounded
electrical
outlet should
NOT be located
within shaded
area
C
L
24"min. 30"min.
22
3
/8" min.
22
7
/8" max.
22
3
/4"*
(critical
dimension)
21
3
/8"
min.
21
7
/8"
max.
Full base
required
to support
150 lbs.
36"min.
required
distance
to floor
20
1
/4"
16
3
/4"
*Critical
dimension –
MUST be
applied
2"(visible
gap)**
21
7
/32"
Power supply location
(left bottom rear)
Allow at least
12" clearance
for door depth
when open
30"
21
1
/4"
22
7
/8"
23
5
/8"
11
/16"
5
/8"