Filter
Top Products
Warmer Drawer
E30WD75GSS designer series
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
USA
•
250 Bobby Jones Expressway
•
Augusta, GA 30907
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
E30WD75GSS 05/08 © 2008 Electrolux Home Products, Inc. Printed in the U.S.A.
30" Warmer Drawer Specifications
•
Product Weight – 49 Lbs.
•
Voltage Rating –120V/450W/60 Hz/15 Amps
•
Connected Load (kW Rating) @120 Volts = 0.45kW (For use on
adequately wired 120V, dedicated circuit having 2-wire service with a
separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @120V = 3.75 Amps
•
Full plywood base required, capable of supporting 100 Lbs.
•
Base must be level and cabinet front must be square.
•
Warmer Drawer can be used alone, or is approved to be used in
combination with any Electrolux ICON
™
Wall Oven. (Refer to
Combination Installation Specifications and drawing on this page.)
•
Warmer Drawer can be used alone, oris approvedto be usedin
combination with any Electrolux ICON
™
built-in product. (Refer to
Combination Installation Specifications pages on web.)
Optional Accessories
•
ServeWare – (5304447729).
Warmer Drawer/Wall Oven Combination Specifications
•
To support Wall Oven when using in combination with Warmer Drawer,
two 3"-wide x 3/4" thick planks must be installed as a base, capable of
supporting 200 Lbs. Do NOT use full base, since planks are necessary
to allow for proper air displacement.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
Overall depth with
drawer fully extended
(including handle) – 44
1
/8"
Full plywood
base required to
support 100 lbs.
4
1
/2" min.
required
distance
to floor
9
7
/8" min.
10
1
/4"max.
28
1
/2" min.
28
3
/4" max.
23
5
/8"min.
24"max.
Warmer Drawer
Stand-Alone
Installation
11
1
/4"
23
3
/8"
30"
25
1
/4"
7
/8"
Power cord
location (right
center rear)
9
7
/8" min.
10
1
/4"max.
1
1
/
2
"
min.
*Critical dimension –
MUST be applied
**Electrical junction
box for Wall Oven
must be lower than
the Warmer Drawer
cutout
†
Maximum height
depends on critical
dimension (
11
5
/
8
")
3"
max.**
30"min.
4" x 4"
opening
to route
armoured
cable
28
1
/2"
min.
28
7
/8"
max.
Electrical
junction box
location
28
1
/2"min.
28
3
/4"max.
Bottom
of oven
cutout
11
5
/8"
min.*
24"*
(critical
dimension)
Two 3" wide
x
3
/4" thick
planks must
be installed,
capable of
supporting
200 lbs.
1
3
/
4
"
min.
†
Warmer Drawer/Single Wall Oven
Combination Installation