Electrolux E36GC70ISS Cooktop User Manual


 
Electric Cooktop Installation
Over 30"Electric Single Wall Oven
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA
250 Bobby Jones Expressway
Augusta, GA 30907
1-877-4electrolux (1-877-435-3287)
electroluxicon.com
CANADA
5855 Terry Fox Way
Mississauga, ON L5V 3E4
1-800-265-8352
electroluxicon.ca
EC_EW INST 05/09 © 2009 Electrolux Home Products, Inc. Printed in the U.S.A.
30" Electric Single Wall Oven Under-Counter
Installation Specifications
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
Single phase 3- or 4-wire cable, 120/240 or 120/208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused
on both sides of line.
Connected Load (kW Rating) @ 240/208 Volts = 4.0/3.0kW
Amps @ 240/208 Volts =16.6/14.4 Amps
Always consult local and national electric codes.
Minimum 23-1/4" clearance for oven door depth when open.
Minimum 24" deep cutout dimension is critical for proper installation,
to ensure that oven’s faceplate will fit flush against cabinet front.
Full oven base of solid plywood or similar material required, capable
of supporting 200 Lbs. Install over two runners and flush with toe plate.
Base must be level and cabinet front must be square with finish-cut
bottom edge.
Side filler panels necessary to isolate oven from adjoining cabinets.
Allow 5" maximum height from oven base to floor, if NO cooktop is
installed directly over wall oven.
Electric Cooktop Installation Over
30" Electric Single Wall Oven Specifications
Electrolux ICON
®
Single Wall Oven models E30EW75GPS and
E30EW75GSS are approved to be used beneath Electrolux ICON
®
electric cooktop models E36IC75FSS, E30IC75FSS, E36IC80ISS,
E30IC80ISS, E36EC70FSS and E30EC70FSS (electric cooktop
models NOT approved for use in this installation are E36EC75HSS,
E30EC65ESS and E36EC65ESS).
For detailed Electric Cooktop installation, refer to model-specific product
page and installation guide on web.
Side filler panels necessary to isolate oven from adjoining cabinets.
Panel height may need to be modified to accommodate the depth of
approved electric cooktop models.
To route armored cable to junction box, cut minimum 4" x 4" opening
in right cabinet side panel.
Allow 4-1/2" maximum height from oven base to floor, if cooktop is
installed directly over wall oven.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
Oven cutout
28
1
/2" min.
28
7
/8" max.
4-1/2" maximum height allowed
from oven base to floor if cooktop
is installed directly over wall oven.
(5" maximum height allowed
with no cooktop.)
240/208V
Junction box
for wall oven
Approx. 3"
24" min.
cutout depth
*Critical dimension – MUST be applied
**For cooktop cutout dimensions refer to model-specific
product page or installation guide on web
240/208V
Junction box
for electric
cooktop
Approx. 3"
36"
min.
Electric Single Wall Oven Cutout
For models: E30EW75GPS
& E30EW75GSS
For all approved electric cooktop models, cut minimum
4" x 4" opening in right cabinet side panel and/or filler
panel, to route armoured cable to junction box
Electric Single Wall Oven Cutout
For models: E30EW75GPS
& E30EW75GSS
Cooktop
cutout**
To route armored cable to junction box through left cabinet side panel
and/or filler panel, cut minimum 4" x 4" opening in wood base and runner
24"min.*
28
1
/2"min.
29"max.
Unit will overlap cutout (minimum) edges by 1"
Install
3
/4" full plywood base on 2 runners, flush
with toe plate, capable of supporting 200 lbs.
Side filler panels necessary to isolate oven from
adjoining cabinets. Panel height may need to
be modified to accommodate the depth of approved
electric cooktop models