Filter
Top Products
1919
1919
19
Care and cleaning
The efficiency of the range hood system depends on
the cleanliness of the intake and filters.
The frequency of cleaning depends on the amount
and type of cooking.
• Do not use the ventilating system without the
filters in place or with grease-laden filters or
surfaces.
To avoid risk of fire and explosion do not use
flammable liquids or solvents.
Always unplug or disconnect the appliance from the
power supply before servicing.
Be sure the entire hood (including the filters and light
bulbs) has cooled and grease has solidified before
attempting to clean any part of the appliance.
FiltersFilters
FiltersFilters
Filters
The metal grease filters are made of stainless steel
anodized aluminum and are long lasting.
TT
TT
T
o Remove The Metal Gro Remove The Metal Gr
o Remove The Metal Gro Remove The Metal Gr
o Remove The Metal Gr
ease Filtersease Filters
ease Filtersease Filters
ease Filters
• Turn the fan and lights off.
• Pull the spring release handle.
TT
TT
T
o Replace The Metal Gro Replace The Metal Gr
o Replace The Metal Gro Replace The Metal Gr
o Replace The Metal Gr
ease Filtersease Filters
ease Filtersease Filters
ease Filters
• Reverse procedure.
TT
TT
T
o Clean Filterso Clean Filters
o Clean Filterso Clean Filters
o Clean Filters
••
••
• It is recommended that the filters be washed at
least once a month; they can be washed by hand
or in the dishwasher.
• Drain water through edge holes and let each filter
dry thoroughly before replacing it.
LightsLights
LightsLights
Lights
Before replacing the lamps, switch power off at
service panel and lock service panel disconnecting
means to prevent power from being switched on
accidentally.
NOTE: TNOTE: T
NOTE: TNOTE: T
NOTE: T
urur
urur
ur
n ofn of
n ofn of
n of
f the lights and fan. Allow the lightsf the lights and fan. Allow the lights
f the lights and fan. Allow the lightsf the lights and fan. Allow the lights
f the lights and fan. Allow the lights
to to
to to
to
coolcool
coolcool
cool
befor befor
befor befor
befor
e handling.e handling.
e handling.e handling.
e handling.
If new lights do notIf new lights do not
If new lights do notIf new lights do not
If new lights do not
operate be suroperate be sur
operate be suroperate be sur
operate be sur
e lights are lights ar
e lights are lights ar
e lights ar
e inserted corre inserted corr
e inserted corre inserted corr
e inserted corr
ectly beforectly befor
ectly beforectly befor
ectly befor
ee
ee
e
calling service.calling service.
calling service.calling service.
calling service.
Replace LightsReplace Lights
Replace LightsReplace Lights
Replace Lights
• Remove the inner lamp lens cover by inserting a
small flat blade screwdriver into each of the three
slots and gently prying it free.
NOTE: Do not remove the outer trim ring (lamp
assembly).
• Grasp the bulb and pull it straight out.
• Replace with 12 volt, 20 watt halogen bulbs with
a G4 base SUITABLE FOR USE IN OPEN
LUMINAIRES.
Follow package dirFollow package dir
Follow package dirFollow package dir
Follow package dir
ections, wear gloves, do notections, wear gloves, do not
ections, wear gloves, do notections, wear gloves, do not
ections, wear gloves, do not
touch bulb with your bartouch bulb with your bar
touch bulb with your bartouch bulb with your bar
touch bulb with your bar
e fingers.e fingers.
e fingers.e fingers.
e fingers.
Bulb
• Replace inner cover by inserting the three
retaining tabs into the three slots and pressing
them firmly in place.
Care and cleaning