Fisher & Paykel V3 DS603 Dishwasher User Manual


  Open as PDF
of 12
 
DOUBLE MODELS
SERVICES SPECIFICATIONS
TOE KICK DEPTH
Prefinished & Flat Door 2”-4
3
/
8
” (50-110mm);
Integrated 5” (127mm) less the Toe Kick Panel thickness. Minimum Panel
thickness using the supplied screws is
3
/
8
” (9mm).
# DOOR FRONT HEIGHT
Prefinished & Flat Door 30
5
/
64
” (764mm);
Integrated 28
1
/
4
” (717.5mm) minimum.
THE CAVITY

wNN
.JOUIJDLOFTT
PGDBWJUZTJEFT
JT
w
NN
4DSFX

w
NN
GSPNGSPOUPGDBCJOFUSZ
+
×
+
.PJTUVSF
1SPUFDUJPO
5BQF
w
NN


w
NN

w
NN

wNN
UISPVHIPVUDBWJUZ



w
NN

w
N
N



wNN

w
NN
TFSWJDFTIPMF
JNNFEJBUFMZ
BEKBDFOUUPDPSOFS
DBOCFFJUIFSTJEF
VÕÌiÀÌ«
ÃÌÕÀi
«ÀÌiVÌ
Ì>«i
w
NN
w
NN
NOTE: All depth measurements are taken
from the front face of the adjacent cabinetry.
WARNING!
Be sure the edges of the services hole
are smooth or covered. If the services
hole is through a metal partition the hole
must be protected with the Edge Protector
provided to prevent damage to the power
cord or hoses.
WATER CONNECTION
Recommended HOT
(Maximum 140°F/60°C).
Supplied hose to suit
3
/
8
” (9mm)
male compression fitting.
WATER SOFTENER MODELS
Refer to your DishDrawer® User Guide for
how to set up your water softener.
WATER PRESSURE
DRAIN CONNECTION
Drain Hose Joiner to suit Ø
3
/
4
” ±
5
/
64
”, Ø
5
/
8
” ±
5
/
64
” and
Ø1” ±
5
/
64
” waste tees.
ELECTRICAL CONNECTION
110-120 VAC power outlet, 9 Amps Minimum.
LENGTH OF SERVICES (FROM PRODUCT EXIT POINT)
Drain hose - 88
9
/
16
” (2250mm)
Inlet hose - 68
7
/
8
” (1750mm)
Power supply cord - 44” (1125mm)
NOTE: Services approximately exit product 7
7
/
16
” (189mm) from left;
21
5
/
8
” (550mm) from front; 31
1
/
4
” (793mm) from top.
3
R
Maximum Minimum
Water Softener Models 145 p.s.i. (1000kPa) 14.5 p.s.i. (100kPa)
Other Models 145 p.s.i. (1000kPa) 4.3 p.s.i. (30kPa)



w
NN
%SBXFS0QFO


w
NN


w
NN


w
NN

w
w
NN
w
w
NN
4JEF7JFX


w
NN

w
w
NN

w
NN
5BC

w
NN
#
*
These marks indicate mounting tab screw
locations (refer to step 1 page 7)
Prefinished model shown
* For an Integrated DishDrawer® the
product depth is specified with an
11
/
16
” (18mm) Integrated Panel thickness.
** Depth of product excludes Curvature (1
3
/
16
” (30mm) Prefinished only,)
or Handle.
**
 previous next