Hall sensor
Cycle Selection Options
SERVICE DAT
ASHEET
P/N: 154768201
E
lectronic Series
BK.......................... Black
BU............................Blue
PK............................Pink
R...............................Red
R-BK...............Red/Black
W............................White
Wiring Diagram
Display Codes (LED)
To st ar t
To de lay st ar t
Close and latch door. Press START/CANCEL pad.
Close and latch door. Press DELAY START pad to
select desired delay time.
To se lec t a new
cycle or option
Press desired cycle and/or option pad. The indicator
lights will change. Press START/CANCEL within 15
seconds to begin cycle.
To ca ncel c ycl e Press START/CANCEL. Dishwasher will drain for
90 seconds, then shut off.
For controls
lock ...........
Press and hold the RINSE ONLY or AIR DRY
pad for 3 seconds. To unlock, press and hold the
RINSE ONLY or AIR DRY pad for 3 seconds.
SENSING
WASHING
SANITIZED
DRYING
CLEAN
OPTION LED's Flashing
STATUS LED's Flashing
----------------------Turbidity sensor is checking the condition of the wash/rinse water.
No sensing for LIGHT WASH (UPPER RACK), LIGHT WASH (LOWER RACK) and CHINA/CRYSTAL.
----------------------Wash portion of cycle.
--------------------The SANITIZED criteria has been met. Indicator light will switch off when door is opened.
------------------------ Drying portion of cycle.
------------------------ Shows completion of cycle. Indicator light will switch off when door is opened.
-- HI-TEMP WASH and NO HEAT DRY/POWER DRY OFF LED's flashing indicates power failure has
occurred. Press START/CANCEL pad and reselect desired options and cycle.
-- The STATUS LED's that are lit when the door is opened will flash. Close door.
RINSE AGENT LOW ------- The liquid rinse agent is low. Light will switch off after 5 complete wash cycles or dispenser is
filled.
This information is intended for use by
persons having electrical and
mechanical training and a level of
knowledge of these subjects generally
considered acceptable in the appliance
repair trade. Electrolux Home Products
North America cannot be responsible,
nor assume any liability, for injury or
damage of any kind arising from the
use of this Service Data Sheet.
Operation
or LO..Low liquid in the rinse aid dispenser
..........A power failure has occurred
.........Water heating delay
..........Close and latch the door
ER/ER....Switch Failure
....Hour(s) delay before start
PF
HO or Hd
CL
'01-24'
ER/CE....Configuration Error
ER/uo.....Vent will not close
ER/uF.....Fan not running
PUMP MOTOR
DRAIN MOTOR
VIO
120VAC
60HZ
USER INTERFACE SWITCH
ELECTRONIC
CONTROL
BOARD
P3-2
P6
BU
DISPENSER
R-Y
W
P3- 3
W
W
HEATER
W
HI-LIMIT
THERMOSTAT
TURBIDITY SENSOR/
THERMISTOR
R
P1
WATER VALVE
FLOAT
SWITCH
PK
P3- 1
W
Y
P3-7
P3-8
RINSE AID
LEVEL SENSE
BK
BK
P2- 8
P2- 7
P3-4
P-5
P3-6
DOOR
SWITCH
W
NEUT W
L1 BK
BK
BK
P3-5
P1
BK
P2-1
W
P2-2
R
P2-3
W
The water/service test is a
special function initiated from
the power failure mode or idle
mode.
While in power failure or idle
mode
- simultaneously press the
DRY/AIR DRY and
START/CANCEL pads for 3
seconds.
The dishwasher will then step
through the test cycle per the chart.
Pushing the START/CANCEL pad
will advance the dishwasher to the
next step.
Water/Service Test
27
45
0.4
75
60
90
90
447
60 1
1
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
1
1
0
0
0
1
1
1
0
X
1
1
0
0
0
1
0
0
0
1
1
1
1
1
0
0
0
0
0
1
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
1
1
1
0
0
0
0
0
1
1
2
3
4
FILL/DISPENSER
STEP
TOTAL TIME (SEC)
WATER VALVE
CIRCULATION MOTOR
DRAIN MOTOR
HEATER
DISPENSER
FAN UNIT
SENSING LED
WASHING LED
SANITIZED LED
DRYING LED
CLEAN LED
FILL
WASH/HEAT
PAUSE
WASH/HEAT
WASH/HEAT/DISP.
DRAIN
DRY
TOTAL
CLEAN LED stays on until door is opened or cycle is started.
X - denotes selectable option
5
6
7
8
0
0
0
0
0
0
1
0
(Some models)
(Some models)
0
0
0
0
0
0
P2- 4
P2- 5
P2- 6
BK
W
R
HALL SENSOR
DISPLAY
Y/BL
P2-13
P2-12
BK-W
P2-11
R
P32-6
BK
P32-9
FAN DRY UNIT
R-W
RINSE LED
SENSING LED
0
0
0
1
1
0
0
0
1
RINSE LED
Device being monitored
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
Fan damper
Display flashes when
Detection of failure
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
Turbidity
Fan speedFan speed
Rinse aid
Thermistor
Uo
Tu
HS
UF
HS
Th
RA
Color Code
Display Codes (Readout)
Y-BK.............Yellow/Black