Filter
Top Products
15
NOTE
● The oven temperature adjustments made with this
feature will not change the Self-Clean cycle temperature
or the Broil temperature.
● Each oven may be adjusted individually.
SELF-CLEANING
ADJUSTING THE OVEN TEMPERATURE
Self-Clean Cycle Time Length
The Clean pads control the Self-Cleaning feature. If you
are planning to use the oven directly after a self-clean cycle
remember to allow time for the oven to cool down and the
oven door to unlock. This normally takes about one hour.
So a self-clean cycle will actually take about 4 hours to
complete.
To set the controls for a 3 hour Self-Cleaning cycle
to start immediately and shut off automatically
1. Be sure that the clock is set with the correct time of
day and the oven door is closed.
2. Press Clean pad. “3:00”, “CLn” will appear, “UPPER”
and “CLEAN” will ash in the display. The control will
automatically clean for a 3 hour period.
3. Press Start pad. “DOOR” and “LOCKED” will ash;
“UPPER” and “CLn” will appear in the display and the
clock will return to the time of day.
4. As soon as the control is set, the motor driven oven door
lock will begin to close automatically. Once the door has
been locked the “UPPER”, “DOOR” and “LOCKED”
indicator light will stop ashing and remain on. Also,
the oven icon will appear in the display. Allow about 15
seconds for the oven door lock to close.
Note: If the optional delay Self-Clean is desired, nish
steps 6-9. If Self-Clean is started immediately skip the
remaining steps and continue with “When the Self-Clean
cycle is completed”.
5. Press Start time pad. “UPPER” and “DELAY” will
start ashing and “- - - -” will appear in the display.
6. Press the Up or Down arrow pad until the desired
start time appears in the display.
7. Press Start pad or wait 5 seconds. The display will
return to the time of day.
8. The control will start the self-cleaning at the set start
time, for the period of time previously selected.
When the Self-Clean Cycle is Completed
1. Three long beeps will be heard and “CLn” will
disappear from the display. “UPPER”, “DOOR” and
“LOCKED” will remain in the display until the door is
unlocked. Some models will display “Hot”. The cooling
fan will continue to run until the oven has cooled
down.
2. Once the oven has cooled down for 1 HOUR, and
“UPPER”, “DOOR” and “LOCKED” are no longer
displayed, the oven door can then be opened.
Stopping or Interrupting a Self-Cleaning Cycle
If it becomes necessary to stop or interrupt a self-
cleaning cycle due to excessive smoke or re in the oven:
1. Press Clear off pad.
2. Once the oven has cooled down for approximately 1
HOUR and “UPPER”, “DOOR” and “LOCKED” are no
longer displayed, the oven door can then be opened.
Important Notes when using the Self-Clean Feature:
1. A Self Clean cycle cannot be started if Oven Lockout
feature is active.
2. When Self-Clean cycle is active on one oven, the other
one cannot be used or set for a Self-Clean cycle or any
cooking cycle.
3. If your clock is set for normal 12 hour display mode the
delay Self-Clean can never be set to start more than 12
hours in advance. To set for a delayed Self-Cleaning cycle
12-24 hours in advance see instructions to set control
for the 24 hour time of day display mode.
The temperature in the oven has been preset at the factory.
When rst using the oven, be sure to follow recipe times
and temperatures. If you think the oven is too hot or too
cool, the temperature in the oven can be adjusted. Before
adjusting, test a recipe by using a temperature setting that
is higher or lower than the recommended temperature.
The baking results should help you to decide how much of
an adjustment is needed.
To adjust the oven temperature:
1. Press and hold Bake pad for 6 seconds. The preset
adjustment number will appear and "UPPER" will ash
in the display.
2. To increase the temperature use the Up arrow pad
to enter the desired change. The temperature may be
increased as much as 35°F (19°C). To decrease the
temperature use the Down arrow pad to enter the
desired change. The temperature may be decreased as
much as 35°F (19°C).
3. Press Start pad or wait 5 seconds to accept the
temperature change and the display will return to the
time of day. Press Clear off pad to reject the change
if necessary.