Filter
Top Products
18
PureSource
TM
* Ice and Water Filter (some models)
NOTE: If you purchased a refrigerator with a
PureSource
TM
* Ice and Water filter, please read the following use
and care information.
This ice and water filter system filters water to your ice maker and water dispenser. It is
located in the upper right back corner of the fresh food compartment.
System Startup:
Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter. The filter
cartridge has already been installed in the filter housing at the factory. Refer to the
How The Water Dispenser Works
section
to properly fill the system with water.
Automatic Ice and Water Dispenser
Order new filter cartridges through the
dealer where you bought the refrigerator,
contact the
Customer Care Center
at
1-800-944-9044, or go to our web site at
www.frigidaire.com. It might be good to
order some filter cartridges when you first
install your refrigerator. Be sure to ask for
the
RG-100
PureSource™*
replacement
cartridge.
IMPORTANT: Resetting The Filter Status Light (some models)
After replacing the filter cartridge, it will be necessary to press the
Filter
Status
reset button located on the ice and water dispenser. This will reset
the Filter Status light. Push the reset button until the green, red and amber
lights flash (10-15 seconds). Please refer to the complete dispenser
operating instructions attached to the inside of the freezer door.
On models without a
Filter Status
reset button, there is a set of
Reminder Stickers included in the envelope that the Use & Care Manual
came in. Choose a dated sticker that indicates 6 - 9 months (depending
on your water quality and usage) from the date of installation. Place the
sticker on the front of the filter cup to remind you when it is time to
change the filter.
The
PureSource™
* NGRG-
2000 Ice and Water Filter
System with the RG-100
cartridge is tested and
certified by NSF International,
the nationally recognized and respected,
not for profit, certification organization for
public health safety. The
PureSource™*
system is tested and certified to ANSI/NSF
Standard 42. See performance data sheet
for specifications. This system should not
be used on water that is microbiologically
unsafe or with water of unknown quality
unless the water has been adequately
disinfected before or after traveling through
the filtration system.
• Rated Capacity - 400 gallons
• Rated service flow - .5 GPM
• Maximum Rated Pressure - 100 PSI
• Maximum Operating Temp. - 100° F
* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter
Changing the Filter:
Water conditions vary throughout the world, but changing the water filter every
6 - 9 months normally will ensure the highest possible water quality. The Filter
Status light will turn red after 400 gallons of water has flowed through the ice and
water dispenser (some models). Also, if the filter has been in a refrigerator that
has not been in use for awhile (during moving for example), change the filter
before reinstalling the refrigerator. The dispenser system will also operate without
filtration (with filter cartridge removed).
To change filter:
It is not necessary to turn the water supply off to change the filter.
1. Open freezer door and leave open until filter change is complete.
2. Turn the ice maker’s power switch to the Off (“O”) position (See illustration
on page 16).
3. Hold filter cup firmly, and unscrew towards left (Some water could
leak out as you remove cup. This is normal.). Filter cartridge should come
down with cup. If cartridge remains in housing, pull down gently, while
twisting filter back and forth.
4. Rinse out cup under running water.
5. The large o-ring that seals the filter system sets in the o-ring groove
down inside the cup. Should the o-ring fall out during filter cartridge
replacement, simply place it back in the groove prior to screwing the cup
back in place. If the o-ring becomes damaged, you will need to order one
from the
Customer Care Center
.
6. Discard old filter cartridge.
7. Remove new filter cartridge from packaging and place in cup. The end
with the small o-ring should be up, out of the cup.
8. Screw cup, with filter, back onto housing. Do Not Use Wrench To Reinstall
Cup. Filter cartridge will self-align as cup is tightened. Be sure cup is
completely tightened with
PureSource™
logo facing outward. Do Not
Tighten Past Stop.
9. Turn the ice maker’s power switch to the On (“I”) position.
10. Check for leaks. Open refrigerator door. Wipe any water droplets from the
filter cup. Fill a glass with water. If there is a leak, unscrew filter cup, and
reinsert the filter cartridge. Check placement of large O-ring. Reinstall
filter cup, making certain it is tightened completely.
11. To condition filter system and purge air from water line, fill a glass with
water. Continue flushing the system for approximately 3 minutes to assure
that the purest water possible is stored in the water tank.