GE 175D1807P633 Dishwasher User Manual


 
GEAppliances.com
Problem Possible Cause What To Do
Water does not enter Automatic self-system checks After START is pressed, the washer does several system checks.
washer or enters slowly Water will flow several seconds after START is pressed.
Water valve screens are stopped up Turn off the water source and remove the water connection hoses
from the upper back of the washer. Use a brush or toothpick to clean
the screens in the machine. Reconnect the hoses and turn the water
back on.
Filter clogged or fill hose may Make sure that the water valve filters (blue and orange screen
be kinked must be free of solids) on the unit are not clogged. Turn off water
and check filter by disconnecting hose at machine. Check that fill
hoses are not kinked or clogged.
Energy efficiency This is an energy-efficient washer. As a result, the temperature settings
for this washer may be different than for a non-energy-efficient washer.
Insufficient water supply Make sure that the water supply is turned on. Make sure that the
water faucets are turned to their completely open position.
The washer door is open The washer door must be closed for all washer cycle operations.
If the door is opened during the washer operation, all functions
will stop, including water filling.
Incorrect fill hose connection Make sure that the fill hoses connect the hot water supply to the
hot inlet on the washer and the cold water supply to the cold inlet
on the washer (hot to hot, cold to cold).
Water fill optimization Water may not cover the top level of the clothes. This is normal
for this high-efficiency washer. The water fill is optimized by the
system for best wash performance.
Snags, holes, tears, rips Pens, pencils, nails, screws or Remove loose items from pockets.
or excessive wear other objects left in pockets
Pins, snaps, hooks, sharp buttons, Fasten snaps, hooks, buttons and zippers.
belt buckles, zippers and sharp
objects left in pockets
Wrinkling Improper sorting Avoid mixing heavy items (like work clothes) with light items
(like blouses).
Overloading • Load your washer so clothes have enough room to move freely.
Incorrect wash cycle Match Cycle selection to the type of fabric you are washing
(especially for easy-care loads).
Repeated washing in water that is too hot Wash in warm or cold water.
Grayed or yellowed Not enough detergent Use correct amount of detergent.
clothes
Not using HE (high-efficiency) detergent Use HE detergent.
Hard water Use hottest water safe for fabric.
Use a water conditioner like Calgon brand or install a water
softener.
Water is not hot enough Make sure water heater is delivering water at
120°–140°F (48°–60°C).
Detergent is not dissolving Try a liquid detergent.
Dye transfer Sort clothes by color. If fabric label states wash separately,
unstable dyes may be indicated.
Colored spots Incorrect use of fabric softener Check fabric softener package for instructions and follow
directions for using dispenser.
Dye transfer Sort whites or lightly colored items from dark colors.
Promptly remove wash load from washer.
Water temperature Water supply is improperly Make sure hoses are connected to correct faucets.
is incorrect connected
House water heater is not set Make sure house water heater is delivering water
properly at 120°–140°F (48°–60°C).
Bad odor inside Washer unused for a long time Leave the door slightly open for the water to air dry.
your washer
or not using recommended
Run a Basket Clean cycle (found in the Washer cycles menu)
quality of HE detergent
with 1 cup of bleach or other commercially available product
manufactured for this use such as Tide
®
Washing Machine Cleaner.
See Care and Cleaning/General Maintenance in the Loading and
using the washer section.
Slight variation This is normal Due to the metallic properties of paint used for this unique
in metallic color product, slight variations of color may occur due to viewing
angles and lighting conditions.
21
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions