Filter
Top Products
– 3 –
Installation
ATTENTION INSTALLER:
FOR A QUALITY INSTALLATION,
FOLLOW THESE INSTRUCTIONS.
• REMOVE ANDDISCARD
SKIDBOARDS and bolts used to
hold skidboards.
• Use PADDED HAND TRUCK
to protect refrigerator finish.
• LEAVE TAPE ONDOORS until
refrigerator is in its final location.
• ADJUST FRONT ROLLERS
so that refrigerator is solid and
doors close easily.
• MAKE SUREDOORS ARE EVEN
AT TOP. Check gasket seal.
• SET BOTHCONTROLS TO “5”.
• SET ICEMAKER TO OFF until
water line is connected.
• IMPORTANT: IMMEDIATELYREMOVE ALLCLEAR PROTECTIVE TAPE FROM TRIM.
• TO REMOVE TAPE RESIDUE AND HANDPRINTS, USE APPLIANCE POLISH.
• REMOVE ALLTAPE AND OTHERPACKAGING MATERIAL FROMINSIDE REFRIGERATOR. DO NOT REMOVESERIAL PLATE.
IMPORTANT: PLEASE READ CAREFULLY
FOR PERSONALSAFETY, THIS APPLIANCEMUST BE PROPERLYGROUNDED.
The power cord of this appliance is equipped with a three-prong (grounding) plug that mates with a standard three-prong (grounding) wall receptacle to minimize the
risk of electric shock hazard from this appliance. The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle
is properly grounded.
Where a standard two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded
three-prong wall receptacle.
DO NOT, UNDERANYCIRCUMSTANCES, CUT ORREMOVETHETHIRD(GROUND)PRONGFROMTHEPOWERCORD.
USAGE
SITUATIONS WHERE THE APPLIANCE’S POWER CORD WILL BE DISCONNECTED INFREQUENTLY
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug. However, if you still elect to use an adapter,
where local codes permit, a TEMPORARYCONNECTION may be made to a properly grounded two-prong wall receptacle by the use of a ULlisted adapter which is
available at most hardware stores. The larger slot of the adapter must be aligned to provide proper polarity in the connection of the power cord.
CAUTION: Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal, and not insulated,
and the wall receptacle is grounded through the house wiring. The customer should have the circuit checked by a qualified electrician to make sure the receptacle is
properly grounded. When disconnecting the power cord from the adapter, always hold the adapter with one hand. If this is not done, the adapter ground terminal is very
likely to break with repeated use. Should this happen, DO NOTUSE the appliance until a proper ground has again been established.
USAGE
SITUATIONS WHERE THE APPLIANCE’S POWER CORD WILL BE DISCONNECTED FREQUENTLY
Do not use an adapter plug in these situations because frequent disconnecting of the power cord places undue strain on the adapter and leads to eventual failure of the
adapter ground terminal. The customer should have the two-prong wall receptacle replaced with a three-prong (grounding) receptacle by a qualified electrician before
using the appliance.
MAKE SURE PROPER
GROUND EXISTS
BEFORE USE
PREFERRED
METHOD
ENSURE PROPER
GROUND AND
FIRM CONNECTION
BEFORE USE
TEMPORARY METHOD
(Adapter plugs not
permitted in Canada)
197D3266P001 31-5087 9-00 JR
FRANÇAIS • ESPANOL
HEX-HEAD BOLTS (4)
ROLLERS
TRUCK FROM
SIDE ONLY
CARDBOARD
PROTECTS
DOOR EDGES
MAKE SURE FRONT
ROLLERS DO NOT
REST ON TRUCK
DO NOT
OVER-
TIGHTEN
STRAP
ROLLER
ADJUSTMENT
RAISE
9 IS COLDEST
0 IS OFF
FREEZER FRESH FOOD
5
8
9
4
3
2
1
0
6
7
5
8
9
4
3
2
1
6
7
• At lower left hinge, remove tubing
from the clip.
• Disconnect the water line.
IF NECESSARY TO REMOVE DOORS, REMOVE ALL HINGES.
FOR DISPENSER MODELS:
COLLAR
PRESS THE WHITE COLLAR AS
YOU PULL OUT THE TUBING.
• Push tubing into connector
(
5
⁄
8
″ to
3
⁄
4
″) to prevent leakage.
WHEN INSTALLING DOORS...
5
⁄
8
″ –
3
⁄
4
″
• At upper hinges, disconnect wiring connectors.
• Remove both hinges with each door to prevent
damage to tubing or wiring.
• Reinstall lower hinges and tighten hinge screws firmly.
• Place door on lower hinge pin and install upper hinges.
Tighten upper hinge screws firmly.
• Align both doors evenly at top by adjusting pin on lower
fresh food hinge.
• Reconnect wiring connectors and reinstall hinge covers.
• Reinstall tubing by pushing tubing into connector.
• Put tubing back into clip.
TO REINSTALL DOORS...
HINGE COVER
WIRING
CONNECTORS
TUBING CLIP
FRESH FOOD HINGE
ADJUSTMENT PIN
ALIGN DOORS EVENLY
AT TOP