Filter
Top Products
* The core which is coloured GREEN/YELLOW must be connected to
the terminal which is marked with the letter E or by the earth symbol or
coloured GREEN/YELLOW.
* The core which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.
* The core which is coloured BROWN must be connected to the termi-
nal which is marked with the letter .
If the terminals of your 3 pin plug are unmarked or if your
installation is fitted with a 2 pin plug,consult a qualified
electrician.
If a 10 AMP plug is fitted,fit 53 AMP fuse.
Before placing the dishes in the dishwasher, remove the larger
food debris to prevent the filter from becoming clogged, which
results in reduced performance.
If the pots and pans have baked-on food that is extremely hard
to remove, we recommend that they be allowed to soak before
they are washed. This will eliminate the need for extra wash
cycles.
Pull out the rack to facilitate loading the dishwasher.
How to Use the Lower Rack
We recommend that you place the most difficult to clean items
on the bottom rack: pots ,lids, serving dishes and bowls, as shown
in the figure to the right.
It is preferable to place serving dishes and lids on the sides of
the racks in order to avoid blocking the rotation of the top spray
arm.
- Pots, serving bowls, etc. must always be placed face down.
- Deep pots should be slanted to allow the water to flow out.
- The cutlery basket can be doubled so that only one section
may be used when the cutlery ware load is light. This also makes
space for additional pots and pans, and it can also be placed
in the upper rack.
- Cutlery should be placed in the cutlery basket with the
handles at the bottom; if the rack has side baskets, the spoons
should be placed individually into the appropriate slots. Espe-
cially long utensils should be placed in the horizontal position at
the front of the upper rack.
How to Use the Upper Rack
The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, coffee and tea cups and saucers,
as well as plates, small bowls and shallow pans (as long
as they are not too dirty).
- Position the dishes and cookware so that they do not get
moved by the spray of water.
The upper rack can be adjusted for height by using the
knobs located on the sides of the rack itself (see fig.A).
.5.
Loading the Dishwasher
GB
.6.
Starting the Appliance
GB
Lower Rack Upper Rack
Load for 12 Standard Settings
Starting a wash cycle
After having completed all of the installation steps in the preced-
ing paragraphs, turn on the water to the unit, partially open the
door of the dishwasher, and press the ON-OFF button "A" lo-
cated on the control panel. The "B" indicator light will come on.
At this point, the appliance is on and ready to be programmed.
Setting and Starting a wash Cycle
Choose the desired cycle by pressing the cycle selection button
"P". Each time it is pressed, one of the cycle indicator lights "D"
will come on in succession.
Choose the wash cycle you feel is most appropriate for the type
of dishes that need washing (consult the wash cycle table con-
tained in this manual, especially when first using the appliance).
Close the door and after a few seconds, a short acoustic signal
will sound indicating that the wash cycle has begun and cannot
be modified. If necessary, read the paragraph entitled, "Cancel-
ling or modifying a cycle while underway. "The end of the cycle
will be signalled by a double acoustic sound, and the indicator
light "D" will begin to blink.
Cancelling or modifying a cycle while underway...
Premise: A cycle that is underway can only be modified if it has
only been running for a short time.
Otherwise, the detergent may have already been used, and the
appliance may have already drained the wash water. If this is the
case, the detergent dispenser must be refilled (see the paragraph
entitled, "Loading the Detergent").
To change the cycle currently underway, open the door, press
the "P" programming button and hold it in for about 5 seconds.
Once the cycle has been cancelled, the dishwasher will emit a
short acoustic sound and the relative indicator light will turn off.
To set a new wash cycle, follow the instructions contained in the
paragraph entitled, "Setting and Starting a Wash Cycle."
If you forget to load some of the dishes...
The wash cycle can be interrupted by opening the door carefully
(in order to avoid being sprayed by hot water). When the door is
closed again, the cycle will automatically restart at the point where
it left off.
At the end of the wash cycle...
The end of the cycle will be indicated by a double acoustical
signal and the blinking of the "D" indicator light. Open the door,
turn off the appliance using the ON/OFF switch and turn off the
water supply to the unit. Wait a few minutes before removing the
dishes so as to avoid handling them while still hot (when they
are more susceptible to breakage) and to get better drying results.
Warning
Important wiring instructions for plug UK only
WARNING: THIS APPLIANCE MUST BE BARTHED
The cords in this mains lead are coloured in accordance with the
following code: (see fig.B)
*Green/Yellow *Earth *Blue *Neutral *Brown *Live
Green/Yellow
Blue
Brown
Fig.B
Fig.A
Connecting instructions
As the colours of the cores in the mains lead of this appliance
may not correspond with the coloured markings indentifying the
terminals in your plug proceed as follows: