Filter
Top Products
If over the years the gas taps become stiff to turn it is necessary to lubricate them.
Such operation must be carried out only by qualified Service Engineers.
Warning use the electric ring/hotplate only after reading the paragraph related to choi-
ce of pans specifically with reference to “Use of electric hotplates”.
18
USING THE GAS BURNER
To ignite the burners, place a lighted taper close to the burner, press in and turn the
control knob anti-clockwise.
If the burners have not been used for a couple of days, wait for a few seconds before
lighting the burner, this will allow any air present in the pipes to escape.
For appliances fitted with electronic ignition carry out the following:
• push in and turn the knob anticlockwise to the
★
symbol.
• ignite the burner by pressing the sparker button.
For hobs fitted with automatic ignition simply push in and turn the knob to the
★
symbol.
The ignition system will continue to generate sparks as long as the gas tap is being
pressed.
If the burner is not ignited within 5 seconds, turn the knob to the 0 position and repeat
the operation.
For models fitted with a safety tap (which cuts-off the flow of gas if the flame is acci-
dentally extinguished) the burners are ignited ad described above, but care must be
taken to keep the knob pressed in for 5 or 6 seconds after the flame is ignited.
ATTENTION:
Prior to switching on the gas hob ensure that the burners and bur-
ner caps are correctly placed within their position.
GENERAL ADVICE
For the best results, the flat-bottomed pans size should match the gas burner size as
follows. See fig. pag. 11.
For smaller containers the gas burner should be regulated so that the flame does not
overlap the base of the pan. Vessels with concave or convex base should not be used.
WARNING: If a burner is accidentally extinguehed, turn the knob to the off posi-
tion and do not attempt to re-ignite if for at least 1 minute.
To protect the glass lid from damage and in the interests of safety, the burners/plates
must be turned off and the burner/pan support/plate area must be cool before closing
the lid down.
GB IE
Hob type Burner type Ø pan / pot (cm)
E;H. R/H front burner 12÷18
E;H. L/H front burner 10÷18
E;H. R/H rear burner 18÷24
E;H. L/H rear burner 18÷24
E. Central burner 24÷28
H. Central radial plate CX do not overhang the radiant plate
REGULATING THE MINIMUM FLAME
After lighting the burners, turn the control knob to the minimum setting and then remo-
ve the knob (this can easily be removed by apply a gentle pressure).
Using a small « Terminal» type screwdriver the regulating screw can be adjusted as in
Fig. 7. Turning the screw clockwise reduces the gas flow, whilst turning it anticlockwise
increases the flow – Use this adjustment to obtain a flame of approximately 3 to 4 mm
in length and then replace the control knob.
When the gas supply available is LPG (Bottle gas)- the screw to set the idle flame must
be turned (clockwise) to the end stop.
Screws regulating
(for differend models)
17
Fig.7
Working
burner
little
large
medium
maxi
double ring
G20
G25
ø gas jet
1/100 mm
G30
G31
ø gas jet
1/100 mm
GZ 350
ø gas jet
1/100 mm
G20 20mbar G30 28-30mbar
G31 37mbar GZ350 13mbar
Qn
kW
Qmin
W
l/h
G20
l/h
GZ350
g/h
G30
g/h
G31
G20 25mbar
G30 36mbar
G25 25mbar
G31 30mbar
Qn
kW
Qmin
W
l/h
G20
g/h
G30
Qn
kW
Qmin
W
l/h
G25
g/h
G31
76
101
118
144
141
50
66
80
94
96
104
132
160
190
191
1
1,75
2,5
3,5
3,5
230
360
530
700
1750
95
167
238
333
333
132
232
331
463
463
73
127
182
254
254
71
125
179
250
250
1,2
2
2,8
4
4
260
410
620
830
1900
114
190
267
381
381
87
145
204
291
291
0,9
1,6
2,25
3,2
3,2
230
360
530
700
1750
100
177
255
354
354
64
114
161
229
229
Table of gas consumption 1 W 0,860 Kcal/h
When you have carried out the new gas regulation, replace the old gas rating pla-
te on your appliance with one (supplied with hob) suitable for the type of gas for
which it has been regulated.
USE OF HOB
USER INSTRUCTIONS
This appliance must only be used for the purpose for which it is intended, domestic
cooking, and any other use will be considered improper and could therefore be danger-
ous. The Manufacturer will not be responsible for any damage or loss resulting from
improper use.