Filter
Top Products
8
EN
Start-up and use
Starting the dishwasher
1. Turn the water tap on.
2. Open the door and press the ON/OFF button: you will hear a short
beep and the display and option indicator lights switch on.
3. Measure out the detergent (
see below
).
4. Load the racks (
see Loading the racks
).
5. Select the wash cycle in accordance with the type of crockery
and its soil level (
see Table of wash cycles
), by pressing the P
button.
6. Select the wash options
* (
see adjacent information
).
7. Start the wash cycle by shutting the door: a long beep signals
the start of the wash cycle.
8. Two short beeps and one long one indicate the end of the wash
cycle and the wash cycle number flashes on the display. Open
the door, switch off the appliance by pressing the ON/OFF button,
shut off the water tap and unplug the appliance from the electricity
socket.
9. Wait for a few minutes before removing the crockery, in order
to avoid burns. Unload the racks, beginning with the lower level.
AUTO WASH CYCLES
*: this model of dishwasher is
equipped with a special sensor which can be used to assess the
level of soiling and automatically select the most efficient and
economic wash cycle accordingly.
The duration of the auto wash cycles may vary due to the operation
of the sensor.
- The machine will switch off automatically during certain
periods of inactivity, in order to minimise electricity
consumption.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection process it
is possible to change the cycle, provided that it has only just
begun: open the door, avoiding the escaping steam, and press
and hold the ON/OFF button; the machine will switch off with a
long beep. Switch the machine back on using the ON/OFF button
and select the new wash cycle and any options desired; start the
cycle by closing the door.
Adding extra crockery
Without switching off the machine, open the door, taking care to
avoid the escaping steam, and place the crockery inside the
dishwasher. Close the door: the cycle starts from the point at
which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a power
cut, the cycle stops. It starts again from the point at which it was
interrupted once the door has been shut or once the electricity
supply is restored.
Measuring out the detergent
A good wash result also depends on the correct amount of
detergent being used; exceeding the stated amount does not
result in a more effective wash and increases environmental
pollution.
Only use detergent which has been specifically
designed for dishwashers.
DO NOT USE washing up liquid.DO NOT USE washing up liquid.
DO NOT USE washing up liquid.DO NOT USE washing up liquid.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam
residue remaining in the machine after the cycle has
ended.
The use of tablets is only recommended for
models which offer the MULTI-FUNCTIONAL
TABLETS option.
To achieve the best results from each washing
and drying cycle, powder detergent, rinse aid liquid
and salt should be used.
Compartment A: Washing detergent
Compartment B: Pre-wash detergent
1. Open cover C by pressing button D.
2. Pour in the detergent after consulting
the
Table of wash cycles
:
• For powder detergent use
compartments A and B.
• For detergent in tablet form: when the
cycle requires 1 tablet, place it in
compartment A and close the cover;
when it requires 2, place the second
tablet at the bottom of the appliance.
3. Remove detergent residues from the edges of the compartment
and close the cover until it clicks.
Wash options
If an option is not compatible with the selected was cycle (see
Table of wash cycles), the corresponding LED flashes rapidly 3
times and 2 short beeps will sound.
Delayed start*
It is possible to delay the start time of the cycle by 3, 6 or 9 hours.
1. Press the DELAYED START button: every time it is pressed a
buzzer sounds and the selected period of time is displayed.
2. Select the wash cycle and shut the door: after the beep sounds,
the timer begins counting down.
3. Once this time has elapsed, the indicator light switches off and
the wash cycle begins.
To adjust the delay time and select a smaller period of time, press
the DELAYED START button. To cancel it, press the button
repeatedly until the selected delayed start indicator light switches
off. The wash cycle will start automatically as soon as the door is
shut.
A
B
D
C
* Only available in selected models.