Hotpoint SDW 60 Dishwasher User Manual


 
8
D
ISHWASHER
First of all.
- Turn on the water supply
tap completely.
- Add the correct amount of
detergent.
- Load the baskets correctly.
- Check that the spray arms
rotate freely.
- Close the door securely.
-After performing all the operations
described in the previous para-
graphs, open the appliance door
and press ON-OFF button "A": in-
dicator light "B" comes on. Your ap-
pliance is now on and awaiting
instructions.
Select the wash cycle.
Select the wash cycle by pressing
button "P". Each time this button is
pressed, one of the indicator lights
"E" will come on in sequence, se-
lect the wash cycle most suitable
for the type of dishes to wash (see
‘Programme Chart’).
If the appliance door is shut, press
the Start button "R" and you will
hear a beep; the cycle will start up
within a few seconds.
The dishwasher informs
you.
Your dishwasher has indicator
lights "G" which light up to indicate
the wash cycle phase that is
underway
Modifying a wash cycle in
progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress, if it has
only just started. Keep the RESET
button "R" pressed for about 5
seconds: a prolonged beep will
sound, followed by three short
beeps. Indicator light "G" will turn
off and at this stage, all the settings
will have been cancelled. You are
now free to re-set the correct wash
cycle.
You've left out a dish?
Well, it happens to everyone. Inter-
rupt the wash cycle by pressing the
ON-OFF button, insert the dish you
had forgotten and press the ON-
OFF button again. The cycle will
start up from where you interrupted
it.
Cycle end
The end of the wash cycle is indi-
cated by a double beep and the flash-
ing of the wash cycle indicator light
"G".
Open the dishwasher door, press
the ON-OFF button cutting off the
electricity supply to the appliance.
Turn off the water tap.
Wait a few minutes before unload-
ing the dishes: they are very hot! If
you wait a little while, they dry better
due to the steam.
Empty the lower rack first.
There's been a power
failure or you opened the
dishwasher door
The wash cycle stops and then
restarts when the electricity comes
back on or when you close the door.
How to use your Dishwasher
You decide when it starts.
When you have loaded the dishes,
you can choose when to start your
dishwasher before setting the wash
cycle desired. Press button "D" to
delay the start of the wash cycle by
12, 9, 6 or 3 hours. Each time you
press it, you will hear a short beep
and the indicator light "G"
corresponding to the selected
delay will light up.
Now you can select the desired
wash cycle. Press the start button
"R" and after you hear the beep, the
countdown to the delayed start will
begin.
Once this time is up, the indicator
light will stop flashing and the wash
cycle will begin.
If you have set a 12 hour delay, for
example, once you have selected
the wash cycle, the 12 hour
indicator light will flash followed
by the others in sequence until the
set time delay is up. A quick look at
the indicator lights will keep you
informed of the countdown progress
at all times.
Have you changed your
mind?
If you change your mind, you can
set a shorter time delay: press but-
ton "D" to select it. You need not
reset the wash cycle.
If on the other hand you want to
cancel the delay set and you want
the cycle to start immediately,
press button "D" repeatedly until the
cycle starts and indicator light "G"
corresponding to the cycle start
phase comes on.
Cycle phase and delayed
start indicator light "G"
(1) Flashing to indicate a
delayed start, to remind you that
you have set a delayed start.
(2) On, lit constantly, each light
shows which stage of the wash
cycle is in progress.
Would you like to see
which settings you have
made?
At any time, when the cycle is under
way, if you press button "P", the
cycle in progress indicator light will
light up for a few seconds.
For your own safety,
ensure the door is closed
when the dishwasher is
not in use.