Filter
Top Products
8
GB
The electronic cooking
programmer
This feature allows you to program the oven or the grill
as follows:
delayed cooking time for a specified period;
immediate start for a specified period;
timer.
Button Functions:
: Timer with hours and minutes;
: cooking time;
: end cooking time;
: Manual change;
: set cooking time (to count down);
: set cooking time (to start from zero)
How to reset the digital clock
After the appliance has been connected to the power
supply, or after a power cut, the clock display will
automatically reset to 0:00 and begin to blink.
Press the
and buttons consecutively and
then reset the time (within 4 seconds) using the
and buttons.
The button
advances the hours.
The button
decreases the hours.
The time can also be changed in the following two ways:
1. Repeat all of the steps above.
2. Press the
button, and then use the and buttons
to reset the time.
Manual operation of the oven
Once the time has been set, the programmer
automatically switches to manual mode.
Note: Press the
button to restore the manual mode
after every Automatic cooking session.
Adjusting the volume of the buzzer
After selecting and confirming the clock settings, use
the
button to adjust the volume of the alarm buzzer.
Delayed cooking time for a specified period
The total cooking time as well as the time at which the
cooking will finish must be set. If we assume that the
time display reads10:00:
1. Turn the oven control knob to the setting and tempera-
ture desired (example: static oven mode at 200°C).
2. Press the button
and then set the cooking time
(within four seconds) using the
and buttons.
Supposing the cooking time is set to 30 minutes, the
display will read as follows:
+
Release the button, and within 4 seconds, the current time
will reappear with the m symbol along with the word auto
3. Press the button
and then use the and buttons
to set the time for when the cooking program should
end. Let us imagine this time to be 1:00 p.m.
=
4. After the button has been released, the current time
will be displayed after approximately 4 seconds:
?
When auto is on, it indicates that the length of
cooking time and the time it is due to finish have been
programmed in automatic mode. At this point, the
oven will turn on automatically at 12:30 and turn off
after 30 minutes. When the oven is turned on, the
symbol m will be displayed for the entire cooking time.
The cooking duration can be displayed at any time by
pressing the button
, and the time it is due to finish
may be displayed by pressing the button
.
Once cooking is completed, the timer will ring; to turn
it off, simply press any button except the
and
buttons.
Immediate start for a specified period
By programming just the duration (points 1 and 2 of the
Delayed cooking time for specified period section),
cooking will begin immediately.
To cancel a cooking schedule already programmed
Press the
button, and use the button to set the
time to:
,
then press the manual cooking mode button .
Timer Feature
The timer feature allows you to enter a specific amount
of time and begins to count down. This feature does not
turn the oven on or off; it merely sounds when the time
has elapsed.
When the button
has been pressed, the display will
read as follows:
,
Then use the and buttons to set the desired time.
As soon as the button has been released, the timer will
start to count down and the current time will be displayed.
.
After the time has expired, an audible signal will be
emitted, which can be turned off by pressing any button
(except the
and buttons). At this point the symbol
will also turn off.
Correction/Cancellation of data
The data entered can be changed at any time by
pressing the corresponding button and the
or
buttons.
When the data for the cooking duration is cancelled,
the data for the time cooking is due to end is also
cancelled automatically, and vice versa.
If the oven has already been programmed, it will not
accept times for the end of cooking which are before
the start of the programmed cooking process.