Filter
Top Products
6
Installation
Choose where you want to
install your dishwasher, you
can place it so that its sides
or back panel are side by
side with furniture or up
against the wall. The
dishwasher is provided with
water supply and drain
hoses, which can be
directed towards the left or
right to facilitate appropriate
installation.
Levelling.
Once the appliance is
positioned, adjust the feet
by screwing them in or out
depending on how high you
want it and to level it so that
it is horizontal. Make sure
that it is not inclined more
than 2 degrees. If the
appliance is level, it will
help ensure its correct
operation.
Cold water connection.
Connect the cold water
supply hose, and making
sure that it is fastened
tightly in place. If the water
hoses are new or have been
out of use for an extended
period of time, let the water
run to make sure it is clear
and free of impurities before
making the connection. If
this precaution is not taken,
the water inlet could get
blocked, causing damage to
your dishwasher.
Standpipe:
Ensure that the hose is not
pushed too far down the
standpipe.
If the end of your drain hose
is fitted with ‘retaining flaps’,
ensure they are inserted fully
into the standpipe. This will
prevent the pipe from
jumping out during
installation and use.
DO NOTDO NOT
DO NOTDO NOT
DO NOT position the
standpipe near an electrical
outlet.
ENSURE that the drain hose
is not kinked and it is routed
as shown in the diagram.
The standpipe should have
a bore of at least 38mm (11/
2”). It should be installed as
shown, have a trap fitted and
must discharge into the
same drain system as your
household sink.
It MUST NOT be connected
to a surface water drain.
Sink Waste System:
For under sink drainage:
Before connecting the drain
hose, remove any internal
restrictions - This will
prevent a build up of debris
which could cause a
blockage.
Remove any restrictions
from the waste spigot and
ensure that the sealing bung
is removed. The hose
should be routed, such that
it is raised to a minimum
height of 800mm (31/2”).
NOTE:NOTE:
NOTE:NOTE:
NOTE: Ensure the sink
outlet pipe has a minimum
diamtere of 32mm.
1. Untie the end of the
GREY drainage hose from
the rear of the appliance.
2. Reposition the ‘Hooked
End Support’ as required
along the GREY drainage
hose.
3. If fitting an under sink
waste disposal unit, cut
out the membrane, bung or
blanking plug.
Ensure the drain hose is
securely attached, to
prevent it coming away
while the machine is in use
and causing a flood.
Connect to the Water
Supply...
- For your dishwasher to ope-
rate correctly it requires
water pressures in the range
of 6-150 psi (100-1000KPa).
Most cold water supplies will
be in this range. NOTE: low
water pressure will lead to
excessively long fill times or
no fill.
- Ensure that the new hose
supplied is connected and
the old hose is disposed of
safely.
- Ensure the fill hose is only
fitted to the cold water
supply.
DO NOTDO NOT
DO NOTDO NOT
DO NOT
overtighten the hose
connector, hand tight is
sufficient.
- Ensure the fill hose is not
kinked.
- Tap connections (if
applicable): A range of
adaptors are available to
suit your tap.
- DO NOT- DO NOT
- DO NOT- DO NOT
- DO NOT connect the
dishwasher to a single outlet
instantaneous water heater
or an electric heater.
Drain hose connection.
WARNING:WARNING:
WARNING:WARNING:
WARNING: Connect your
dishwasher drain hose to
pipes which connect to the
foul drain system and not to
surface water drains.
IMPORIMPOR
IMPORIMPOR
IMPOR
TT
TT
T
ANTANT
ANTANT
ANT
::
::
: For the correct
operation of your
dishwasher, it is essential to
comply with the following
information:
Remember you will be charges for a service call is a
problem with your appliance is caused by incorrect
installation or misuse.
Anti-flooding protection
Your dishwasher is provided
with a special system which
blocks the water supply in
the event of leaks inside the
appliance.