Filter
Top Products
IMPORTANT:Becauseaircirculatesbetweenbothsections,any
odorsformedinonesectionwilltransfertotheother.Youmust
thoroughlycleanbothsectionstoeliminateodors.Toprevent
odortransferfromfood,wraporcoverfoodstightly.
ElectronicControls(onsomemodels}
Foryourconvenience,yourcontrolsare preset at the factory,
When installing your refrigerator, make sure that the controls are
still preset to the "mid-settings" as shown.
FREI_B{ REFRI6ERATOR
OOOOOOO OOOOOOO
1 = _ @ 5 0 7 i = _ @ s i 7
To turn on refrigerator:
• Press and hold ON/OFF for 2 seconds. The indicator lights
show the current temperature control settings.
NOTE: Settings to the left of the mid-setting make the
temperature less cold. Settings to the right of the mid-setting
make the temperature colder.
IMPORTANT:
• The Refrigerator Control adjusts the refrigerator compartment
temperature. The Freezer Control adjusts the freezer
compartment temperature.
• Wait 24 hours after you turn on the refrigerator before you put
food into it. If you add food before the refrigerator has cooled
completely, your food may spoil. Adjusting the Refrigerator
and Freezer Controls to a colder setting will not cool the
compartments any faster.
• If the temperature istoo warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked, before adjusting the controls.
• The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
Adjusting Electronic Controls
NOTE: Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
If you need to adjust temperatures:
• Press the FREEZER or REFRIGERATOR arrow to move the
indicator light to the right, one setting at a time. Continue
moving the indicator light until the desired setting is reached.
• o o
z s 7 I
NOTE: With each press of the arrow, you will hear a beep as
the light moves to the next setting. The indicator light moves
to a setting of "7" and then returns to the setting of "1 ".
CONDITION: SETTING ADJUSTMENT:
Refrigerator too cold REFRIGERATOR Control
- Not set correctly for one setting lower
conditions
Refrigerator too warm REFRIGERATOR Control
- High use or room very warm one setting higher
FREEZER too cold FREEZER Control one
- Not set correctly for setting lower
conditions
Freezer too warm/too little ice FREEZER Control one
- High use or heavy ice usage setting higher
Additional Electronic Control Panel Features
Additional features are located on the control panel at the top of
the refrigerator compartment.
Water Filter Indicator Light and Reset
NOTE: Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before
or after the system.
The water filter display will help you know when to change your
water filter cartridge. To change your filter, see the "Changing a
Base Grille Filter" section.
INDICATOR: STATUS:
GOOD (green) New filter installed
ORDER (yellow) Order filter, 10% filter life remains
REPLACE (red) or when Replace water filter
water flow decreases
• After changing the water filter cartridge, reset the water filter
indicator by pressing and holding the RESET for 2 seconds.
The status light will change from Replace (red) to Good
(green) when the system is reset,
_O
Accelerated Ice Production
The accelerated ice feature assists with temporary periods of
heavy ice usage by increasing ice production over a 24-hour
period.
• Press ICE touch pad to set the freezer temperature to -10°F
(-23°C). The Accelerated Ice setting will remain on for 24
hours unless manually turned off.
If increased ice production is desired at all times, set the
Freezer Control to a colder setting. Adjusting the freezer to a
colder temperature may make some foods, such as ice
cream, harder.
10