Kenmore 10657076601 Refrigerator User Manual


 
Remove the Handles (optional) Replace the Doors and Hinges
Style 1
1. Apply firm pressure with your hand on the face of trim. Slide
top trim up and bottom trim down away from handle. Lift trim
pieces oft shoulder screws. See Graphic 1.
2. Remove handle screws and handles. See Graphic 1.
3. Move refrigerator into place. Replace handles as shown. See
Graphic 1.
Style 2
1. Apply firm pressure on the handle to slide it up and oft of the
shoulder screws. See Graphic 1.
2. Move refrigerator into place. Replace handles as shown. See
Graphic 1.
Remove the Doors
E_ectrical Shock Hazard
Disconnect power before removing doors.
Failure to do €o can result in death or eiectrica_ chock.
1. Unplug refrigerator or disconnect power.
2. Open both refrigerator doors. Remove the base grille. Place
hands along the ends of the grille. Push in on the top of the
base grille and pull up on the bottom. See Graphic 2.
3. Close both doors and keep them closed until you are ready to
lift them free from the cabinet.
4. If you have a dispenser (ice or water), disconnect the water
dispenser tubing located behind the base grille on the freezer
door side. See Graphic 3.
Press the red outer ring against the face of fitting and pull
the dispenser tubing free.
On some models, remove the tubing from hose clip.
5. Remove the top left hinge cover and screws as shown. See
Graphic 4.
IMPORTANT: Do not remove screw A.
6. Disconnect wiring plug. Remove remaining left hinge screws
and hinge as shown in Graphic 4.
IMPORTANT: Do not remove screw A.
7. Lift freezer door straight up off bottom hinge. See Graphic 5.
The water dispenser tubing remains attached to the freezer
door and pulls through the bottom left hinge. Make sure you
protect the dispenser tubing from damage.
8. Remove the top right hinge cover and screws as shown in
Graphic 6.
IMPORTANT: Do not remove screw A.
9. Lift the refrigerator door straight up off bottom hinge.
10. It may not be necessary to remove the bottom hinges to
move the refrigerator through a doorway. Both bottom hinges
have similar construction.
If necessary, disassemble the hinges as shown in
Graphic 7.
IMPORTANT: Do not remove screw A.
1=
2.
Replace both bottom hinges, if removed. Tighten screws.
Feed the dispenser tubing through the bottom left hinge
before replacing the freezer door on the hinge. Assistance
may be needed.
NOTE: Provide additional support for the doors while the top
hinges are being replaced. Do not depend on the door
magnets to hold the doors in place while you are working.
3. Reconnect water dispenser tubing by pushing tubing into
fitting until it stops and black mark touches face of the red
outer ring. See Graphic 3. On some models, replace tubing in
hose clip.
4. Align and replace the top left hinge as shown. See Graphic 4.
Tighten screws.
5. Reconnect wiring plug.
6. Replace left hinge cover and screw.
7. Replace the refrigerator door by carefully lifting the door onto
the bottom right hinge.
8. Align and replace the top right hinge as shown. See
Graphic 6. Tighten screws.
9. Replace hinge cover and screws. Tighten screws.
10. Plug in refrigerator or reconnect power.
Door Closing
1. Place a level inside the refrigerator at the back of the top
shelf. See Graphic 8 in "Refrigerator Doors."
2. Locate the leveling screws behind the base grille of the
refrigerator on either side.
3. Use a hex-head socket wrench to adjust the rear roller
leveling screws until the refrigerator is level. Turn the rear
roller leveling screw to the right to raise that side of the
refrigerator or turn the leveling screw to the left to lower that
side. See Graphic 10 in "Refrigerator Doors." Make sure
refrigerator is level before proceeding.
4. Check the door alignment after leveling the refrigerator.
Align the Doors
IMPORTANT: First level the back of the refrigerator as described
in "Door Closing."
The doors may be uneven after leveling the refrigerator. See
Graphic 9 in "Refrigerator Doors." The doors are preset at the
factory so that the refrigerator door is higher than the freezer door
by approximately the thickness of a quarter. Once the doors are
loaded with food, they should be even. If the door height needs
to be adjusted after the doors have been loaded with food, follow
these steps.
1. Use a hex-head socket wrench to adjust the front roller
leveling screws until the doors are even. Turn the front roller
leveling screw to the right to raise that side of the refrigerator
or turn the leveling screw to the left to lower that side. See
Graphic 10 in "Refrigerator Doors."
NOTE: Open and close both the refrigerator and freezer
doors after each adjustment to check the door alignment.
2=
Open the doors and replace the base grille. Line up the grille
support tabs with the metal clips. Push the grille firmly to
snap it into place.
NOTE: Be sure to refasten the Tech Sheet behind the base
grille.