Filter
Top Products
.,,,,,,,,, ,,
Where to fill
Top of 3rd step (3 tbs or 45 g)
Top of 2nd step (2tbs or 30 g)
Filling the dispenser
The rinse aid dispenser holds 6 oz (175 mL) of rinse aid. Under
normal conditions, this will last for about three months. You do
not have to wait until the dispenser is empty to refill it. Try to keep
it full, but be careful not to overfill it.
1. Make sure the dishwasher door is completely open.
2. Remove the Fill Indicator cap.
3. Add rinse aid. Fill to the smallest opening in the lower part of
the dispenser. Overfilling can cause the rinse aid to leak out,
and could cause oversudsing.
Water Hardness
Topof let step (1 tb or 15 g)
Amount of Detergent
Soft to Medium
Hard Water
0 to 6 grains per
gallon
For normally soiled loads
• Fill the Main Wash section to the
top of the 2nd step (2 tbs or 30 g)
• Fillthe Pre-Wash section to the
top of the 2nd step (2 tbs or 30 g)
if needed
NOTE: Add only 1tb or 15 g of
detergent to both sections if dishes
are pre-rinsed or the water isvery
soft (0 to 2 grains per gallon).
For heavily soiled loads
• Fill the Main Wash section to the
top of the 3rd step (3 tbs or 45 g)
• Fill the Pre-Waeh section to the
top of the 2nd step (2 tbs or 30 g)
Medium to Hard
Water
7 to 12 grains per
gallon
For normally soiled and
heavily soiled loads
• Fill the Main Wash section to the
top of the 3rd step (3 tbs or 45 g)
• Fill the Pre-Wash section to the
top ofthe 2nd step (2 tbs or 30 g)
if needed
NOTE: Fill amounts shown are for standard powdered detergent.
Amounts may vary if you use liquid or concentrated powdered
detergent. Follow instructions on the package when using liquid
dishwasher detergent or concentrated powdered detergent.
Rinse Aid Dispenser
Rinse aids prevent water from forming droplets that can dry as
spots or streaks. They also improve drying by allowing water to
drain offof the dishes during the final dnee by releasing a small
amount of the rinse aid into the rinse water. Your dishwasher is
designed to use a liquid rinse aid. Do not use a solid or bar-type.
Checking the dispenser
Check the center of the Fill Indicatorcap. Clear means it needs
filling.
Or you can remove the Fill Indicator cap. If an "E" is visible, the
dispenser isempty.
4. Clean up any spilled rinse aid with a damp cloth.
5. Replace the Fill Indicator cap. Close tightly.
Dishwasher Efficiency Tips
Hot water dissolves and activates the dishwashing detergent, mill
Hot water also dissolves grease on dishes and helps glasses dry
spot-free. For best dishwashing results, water must be at least
120°F (49°C) as it enters the dishwasher. Loads may not wash as
well if the water temperature is too low.
p,
To check water temperature
1. Run hot water at the faucet closest to your dishwasher for at
least 1 minute.
2. Place a candy or meat thermometer in a glass measuring
cup.
3.
4,
a
Check the temperature on the thermometer as the water is
running into the cup.
If the water temperature at the faucet is below 120°F (49°C),
have a qualified person raise the water heater's thermostat
setting.
To save water, energy and time, do not rinse dishes before
putting them into the dishwasher.
Use a low energy, quick, or short cycle whenever possible.
These cycles use less hot water and energy than the Normal
cycle.
Use a delay feature (on some models) to run your dishwasher
during off-peak hours. Local utilities recommend avoiding
heavy usage of energy at certain times of day.
During the summer, run your dishwasher at night. This
reduces daytime heat buildup in the kitchen.
Use the energy-saving dry option whenever possible. Allow
longer drying times (overnight) when using these options. Use
a rinse aid to improve drying.
Use cycles or options that add extra heat to the wash or rinse
portion of the cycle only when needed.
Run your dishwasher with full loads. Run a rinse cycle after
meals until the dishwasher is full.
11