Filter
Top Products
NOTE: The sensor in your dishwasher monitors the soil level.
Cycle time and/or water usage can vary from the numbers above
as the sensor adjusts the cycle for the best wash performance.
1,
2.
Press CANCEL/DRAIN. The Cancel/Drain light glows.
The dishwasher starts a 2-minute drain (if needed). Let the
dishwasher drain completely. The light turns off after
2 minutes. The door must be closed for the dishwasher to
drain.
To stop the drain
Youcan press CANCEL!DRAIN again to stop the drain. Be sure
to drain the dishwasher before starting a new cycle.
To clear the indicators
Press CANCEL!DRAIN before starting the dishwasher to clear all
options and cycles.
During the first minute of a cycle
1. Select a new cycle and/or options.
2. Check the detergent dispensers. They must be filled properly
for the new cycle.
3. The Start/Resume light will flash when the door is opened.
Make sure the door is closed.
Press START/RESU M E.4,
After the first minute of a cycle
1.
Press CANCEL!DRAIN. The Cancel/Drain light glows. Your
dishwasher starts a 2-minute drain (if needed). Let the
dishwasher drain completely.
2. Check the detergent dispensers. They must be filled properly
for the new cycle.
3. Make sure the door is closed. The Start/Resume light will
flash.
4. Select a new cycle and/or options.
5. Press START/RESUME.
You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop before opening the door. The Start/Resume
light will flash.
2. Open the door. If the detergent dispenser cover is still closed,
add the item.
3. Close the door firmly until it latches. The Start/Resume light
will flash.
4. Press START/RESUME.
IMPORTANT: If Lock On is selected, turn off the lock (see Lock
On section in "Option Selections"), or the Start/Resume light will
continue to flash.
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn off the option,
or select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
anytime before drying begins.
Press START/RESUME to use the same cycle and option(s) as
the previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press START/RESUME, the dishwasher runs the last full
wash cycle and options.
High Temp
Select this option to increase the water temperature during the
wash portions of the cycle. High Temp raises the water
temperature to 145°F (63°C), in the main wash. Heating the water
helps improve washing results. High Temp is useful when loads
contain tough food soil.
This option may add heat and wash time to the cycle.
NOTE: High Temp is an option with the SMARTWASH TM, Pots
Pans and Normal Wash cycles.
Sani Rinse (on some models)
Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C). Sani Rinse adds heat and time to
the cycle. This high temperature rinse sanitizes your dishes and
glassware in accordance with NSF/ANSl Standard 184 for
Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments.
NOTE: Sani Rinse is an option with SMARTWASH TM, Pots Pans,
and Normal Wash cycles. Only these sanitization cycles have
been designed to meet the NSF/ANSl requirements.
Heated Dry
The Heated Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY
so that the light goes off. However, you will have items in your
dish load that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Quick
Rinse.
12