Filter
Top Products
3
to produce steam to froth milk after having brewed
coffee
1Ensure that the pod filter holder with a pod holder is fitted to the coffee maker.
2Press the steam button and its light will flash (see Fig. D page ii). When the
steam indicator light glows continuously the unit is ready to produce steam
(see Fig. E page ii).
3 Place an empty jug under the steam/hot water nozzle and move the function
lever to the lower steam position ( ) to remove excess water from the system.
Return the function lever to the middle ( ) position and discard the water.
4 Part fill a jug with milk – the milk may increase up to three times in volume so
select a suitably sized jug.
●
Fresh cold semi skimmed milk gives the best results.
5 Position the jug under the steam/hot water nozzle
6Place the nozzle into the milk and move the function lever to the lower steam
position ( ). The milk will begin to increase in volume and appear frothy ᕦ. To
obtain a creamier froth, rotate the jug with slow movements from the bottom
upwards.
7 Once the desired temperature and froth are obtained, stop the steam by
returning the lever back to the middle ( ) position.
●
Never allow the milk to boil as this will spoil the flavour of the coffee.
8 Pour the frothed milk into the cups containing the espresso coffee to make a
cappuccino.
9Switch off the steam button in order to make further cups of coffee.
Note: After having used the steam function. The OK indicator light will flash
quickly (once per
1
⁄4 second) for a short period to indicate the high temperature
(see Fig. F page ii) during which period of time the machine is not ready for
brewing coffee. Wait until the OK indicator light glows continuously (see Fig. G
page ii) otherwise the temperature will be too high and will burn the coffee.
hint
●
After frothing milk, dispense hot water from the steam/hot water nozzle (see
below) which will help clean the nozzle and help the boiler to cool down more
quickly.
to produce hot water for other drinks, eg tea, fruit
drinks
1Ensure that the pod filter holder with a pod holder is fitted to the coffee maker.
2Press the power on button and its light will glow and the OK indicator light will
flash.
3 When the OK indicator light stops flashing and glows continuously, place a cup
under the steam/hot water nozzle and move the function lever to the lower
steam position
( ). Hot water will dispense from the nozzle.
4 Switch off and unplug after use.
●
Never use teabags in the pod filter.
setting the dispensing volume
The coffee maker has been programmed to dispense a pre selected quantity of
liquid which is 40ml for Espresso, 125ml for a single café crema and 250ml for
a double café crema. These volumes can only be changed by carrying out the
following procedure ensuring that the appropriate coffee pod and pod filter are
fitted.
1 Place the required cups(s) under the coffee nozzle.
2Press and hold the Steam button for 5 seconds during brewing and the OK and
steam indicator lights will flash simultaneously. When the coffee volume in the cup
reaches the required level, release the button and the water volume will be stored in
the memory. This can be re-programmed at any time following the above
procedure.
descaling
When the power on indicator light starts flashing the machine needs to be
descaled and it will continue to flash until the unit is descaled.
1With the machine switched off, place a jug under the steam/hot water nozzle.
(This may need to be emptied during the descaling process.)
2 Fill the water tank to the Max level with a liquid descaling agent (follow the
manufacturers guidelines).
3 Fit the pod filter holder (with pod filter fitted) to the coffee maker.
4Press the power on button. Both the power on and OK indicator lights will
flash.
5 When the OK indicator light stops flashing, turn the function lever to the lower
steam position ( ).
6Press the Steam button for three seconds. This will activate a descaling
program and the 3 indicator lights (On/Off, OK and Steam) will flash in
succession indicating the descaling cycle is in operation. (During this time the
pump will operate 30 seconds On followed by 2 minutes Off). Allow the entire
descaling agent to flow out from the steam/hot water nozzle. The machine will
bleep when the tank is empty.
7 When the tank is empty return the function lever to the middle ( ) position. (The
indicator lights will continue to flash).
8 Rinse the tank and fill with fresh water.
9Turn the function lever to the lower steam position ( ) and allow all the fresh
water to flow out from the steam/hot water nozzle. (During this cycle the pump
will operate continuously until the tank has emptied and the coffee maker will
bleep.)
10 Turn the function lever to the middle ( ) position
11 Hold down the steam button for 3 seconds to reset the descale cycle and the
indicator lights will stop flashing.
12 The coffee maker is now ready for use.
cleaning
1 Before cleaning, unplug and let everything cool.
2 Never immerse the appliance in water
3 Don’t wash parts in the dishwasher.
tank, pod filter, pod filter holder
●
Wash, rinse and allow to dry
steam/hot water nozzle
●
Prior to cleaning allow some hot water to flow out of the nozzle (see ‘to
produce hot water for other drinks’ ) then unplug and allow to cool before
proceeding.
●
Unscrew the nozzle by turning anti-clockwise, then wash thoroughly. Check
that the hole in the nozzle is not blocked. If necessary unblock with a pin.
●
Clean the steam/hot water delivery tube. Make sure the end is not blocked .
●
Screw the nozzle back onto the delivery tube.
drip tray/drip tray cover
●
Empty the drip tray regularly.
1Wash then dry thoroughly.
service and customer care
●
If the cord is damaged it must, for safety reasons, be replaced by Kenwood or
an authorised Kenwood repairer.
UK
If you need help with:
●
using your machine or
●
servicing, spare parts or repairs (in or out of guarantee)
టcall Kenwood customer care on 023 9239 2333. Have your model
number ready – it’s on the underside of the coffee maker.
●
spares and attachments
టcall 0870 2413653.
●
other countries
Contact the shop where you bought your machine.
guarantee (uk only)
If your coffee maker goes wrong within one year from the date you bought it, we
will repair it (or replace it if necessary) free of charge provided:
●
you have not misused, neglected or damaged it;
●
it has not been modified (unless by Kenwood);
●
it is not second-hand;
●
it has not been used commercially;
●
you have not fitted a plug incorrectly; and
●
you supply your receipt to show when you bought it.
This guarantee does not affect your statutory rights.