Filter
Top Products
before using your Kenwood appliance
●
Read these instructions carefully and retain for future
reference.
●
Remove all packaging and any labels.
safety
●
Ensure the cord is fully unwound from the cord wrap
before using the handmixer.
●
Never put the handmixer body in water or let the cord
or plug get wet.
●
Keep fingers, hair, clothing and utensils away from
moving parts.
●
Never let the cord touch hot surfaces or hang down
where a child could grab it.
●
Never use a damaged handmixer. Get it checked or
repaired: see 'service and customer care'.
●
Never use an unauthorised attachment.
●
Always unplug the appliance when not in use, before
fitting or removing parts or before cleaning.
●
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
●
Children should be supervised to ensure that they do
not play with the appliance.
●
Only use the appliance for its intended domestic use.
Kenwood will not accept any liability if the appliance is
subject to improper use, or failure to comply with these
instructions.
before plugging in
●
Make sure your electricity supply is the same as the
one shown on the underside of your handmixer.
Important – UK only
●
The wires in the cord are coloured as follows:
Blue = Neutral, Brown = Live.
●
The appliance must be protected by a 3A approved
(BS1362) fuse.
Note:
●
For non-rewireable plugs the fuse cover MUST be
refitted when replacing the fuse. If the fuse cover is lost
then the plug must not be used until a replacement can
be obtained. The correct fuse cover is identified by
colour and a replacement may be obtained from your
Kenwood Authorised Repairer (see Service).
●
If a non-rewireable plug is cut off it must be
DESTROYED IMMEDIATELY. An electric shock hazard
may arise if an unwanted non-rewireable plug is
inadvertently inserted into a 13A socket outlet.
●
This appliance conforms to EC directive 2004/108/EC
on Electromagnetic Compatibility and EC regulation no.
1935/2004 of 27/10/2004 on materials intended for
contact with food.
before using your handmixer for the first time
●
Wash the parts (see 'cleaning').
key
ቢ speed switch
ባ tool release button
ቤ beaters
ብ cord wrap
ቦ kneader with additional collar
ቧ kneader without additional collar
ቨ beater storage pillars
ቩ kneader storage pillars
ቪ worktop storage unit
ቫ cord clip
to use your handmixer
1 Unwrap the cord from the cord wrap and make sure
the speed switch is in the off position by lining up the O
symbol on the handmixer body with the dot on the side
of the speed switch. Insert the beaters or kneaders –
turn and push until a positive click is felt. The tabs on
the tool shafts need to line up with the outlet holes.
Important: The kneader with the additional collar will
only fit into the larger outlet hole.
2 Plug in.
3 With the ingredients in a suitably sized bowl, place the
beaters/kneaders into the bowl.
4 Pull the speed switch backwards to reach the desired
speed (the first dot on the handmixer body is slow and
speed 5 is fast). Line up the dot on the side of the
speed switch with the corresponding speed.
●
As the mixture thickens, increase the speed.
●
If the machine labours increase the speed.
●
Move the speed switch forwards to the pulse position
(P) to operate the motor as required. The motor will
operate for as long as the pulse is held in position.
5 When the mixture has reached the desired
consistency, return the speed switch to the off position
and then lift the beaters/kneaders out of the bowl.
2