Filter
Top Products
9
Ice Service
Models with an Automatic Ice
Maker
Adjustable Ice Level (select models)
Some ice makers are equipped with a sensor arm to adjust
the amount of ice in your ice storage tray for times when
less ice is needed.
To adjust the amount of ice produced: Push the plastic
sensor arm inward and rotate to the desired capacity.
After your refrigerator has been connected to the water
supply, move the wire lever arm into the down position.
This will start its operation. The ice maker will fill with
water when the freezer reaches the proper temperature. It
may be 8 to 12 hours before the ice maker furnishes any
usable ice cubes.
Discard all the cubes from the first two or three batches
made. These initial ice cubes may be irregularly shaped,
discolored, or contain impurities from the new water
supply piping.
When the ice cubes are ejected it is normal for several
cubes to be joined together at the ends. They can easily
be broken apart. The ice maker will continue to make ice
until the supply of ice cubes raises the wire lever arm,
shutting the ice maker off.
To manually stop the operation of the ice maker, move
the wire lever arm into the up (off) position.
Certain sounds may accompany the various cycles of the
ice maker.
• buzzing of the water valve
• running of the water as the tray fills
• rattling of the ice cubes falling into an empty ice bin.
If the ice is not used frequently, the ice cubes will become
cloudy, shrink, stick together and taste stale. Empty the
ice storage bin periodically and wash it in lukewarm
water. Be sure to dry the bin before replacing it.
Dispenser Models
To check the ice level or gain access to the ice bin, lift
open the door on the ice bin.
To remove the bin, first turn off the ice maker. This is
done by opening the door on the ice bin and moving the
ice maker wire lever up to the “off” position. Then reach
under the bin front and pull down on the back edge. After
it snaps free, pull the bin straight forward. To replace the
ice bin, align the bottom rails to the corresponding shelf
grooves and push it straight back until it stops and
latches. Make sure the tabs at the back of the bin that
turn the spiral auger are positioned between the prongs
from the auger motor. Turn the ice maker on by
lowering the wire arm.
Beverages and foods should not be placed in the ice
storage bin for quick chilling. These items can block the
wire lever arm, causing the ice maker to malfunction.
For Your Safety
Do not place fingers or hands on the automatic ice
making mechanism while the refrigerator is plugged in.
Under certain rare circumstances, ice cubes may be
discolored, usually appearing with a green-bluish
hue. The cause of this unusual discoloration is a
combination of factors such as certain characteristics
of local waters, household plumbing and the
accumulation of copper salts in an inactive water
supply line which feeds the ice maker.
Continued consumption of such discolored ice cubes
may be injurious to health. If such discoloration is
observed, discard the ice cubes and contact your
local water utility or water treatment company.
Models Without an Automatic
Ice Maker
The freezer compartment is equipped with ice cube trays
and an ice storage bin. The bin stacks on top of the
stacked ice cube trays. To release the ice cubes from a
tray, hold the tray upside down over the bin and twist
both ends.
The refrigerator is automatic ice maker ready. The
number for the ice maker kit needed appears on the data
plate (see front cover).
ON
OFF
ON
OFF
100
%
75
%
IC
E
L
E
V
E
L
50
%
IC
E
L
E
V
E
L
50
%
75
%
100
%
100
%
75
%
ICE
LEVEL
50
%
ICE
LEVEL
50
%
75
%
100
%
Note: Energy rating guides that are posted on the
refrigerator at the time of purchase do not include
optional ice maker energy usage.