Melissa 645-261 Hot Beverage Maker User Manual


  Open as PDF
of 25
 
15
PRIOR TO FIRST USE
Before using for the first time (or after a long
period of storage), fill and boil the appliance
three times.
1. Readthesafetyinstructionsthrough
carefully.
2. FillwithwatertotheMAXmarkonthe
inside.
3. Switchonasdescribedunder"Usingthe
Appliance".Allowthewatertoboil.
4. Pour the water out once it has boiled.
Repeatsteps2-4twicemore.Theapplianceis
now ready for use.
USING THE APPLIANCE
1. Openthelid(3)bypressingtherelease
button (4).
2. Pourfreshwaterintothekettle.The
appliance must be filled up to the minimum
mark ("MIN") and contain no more than up
tothemaximummark("MAX").Themarks
are on the inside of the appliance.
3. Closethelidandensureitclicksintoplace.
4. Place the kettle on its base (10) by
positioning it so the stud on the base (2) fits
into the hole on the underside of the kettle.
5. Plug the base in (9) and check that it is
switched on at the wall.
oCaution!Ifyousettheon/offswitch
(6) to the "I" position before replacing the
kettle on the base, the kettle switches on
automatically when replaced on the base.
Forsafety’ssake,checktheon/offswitch
position before replacing the kettle on the
base to avoid accidentally starting the
kettle.
6. Switch on the appliance by switching the
on/offbuttonto"I".Theindicatorlamp(5)
will be on when the appliance is on and
heating the water.
Thewaterwillboilwithinafewminutes,
depending on the amount in the kettle. If you
want to interrupt the boiling, you can do this
atanytimebyswitchingtheon/offbuttonto
"O".Oncethewaterisboiling,thekettlewill
automatically switch off thanks to the integrated
thermostat.Theindicatorlampwillgooutwhen
theapplianceisswitchedoffandtheon/off
buttonwillrevertto"O".
Anti boil-dry device
If you switch the kettle on without there being
any water in it or when the water level is below
"MIN",theantiboil-drydevicewillautomatically
switchitoff.Thekettlecanbeswitchedon
normally as soon as it is filled with a sufficient
amount of water.
Storage
If the kettle is to be stored for any length of time
without use, the cord can be rolled up around
theinsideofthebase.Ensuretheapplianceis
clean and dry before storing.
CLEANING
When cleaning the appliance, you should pay
attention to the following points:
• Removetheplugfromthewallsocketand
allow the appliance to cool down before
cleaning.
• Donotimmerseinwateroranyotherliquid.
• Wipeusingawell-wrungclothandhot
water.Alittledetergentcanbeaddedifthe
appliance is heavily soiled.
• Neverusescouringpowder,steelscourers
or other strong cleaning agents to clean the
interior or exterior surfaces of the appliance,
as they may scratch the surfaces.
• Makesurethatnowatergetsintothe
connector on the base or the hole in the
underside of the kettle.
Descaling
Thelimecontentofordinarytapwatermeans
limescale may gradually be deposited inside.
Thislimescalemaybeloosenedusingacetic
acid(NOTordinaryvinegar)ordescaler,
available in supermarkets, etc.
1. Mix100mlaceticacidwith300mlcold
water, or follow the instructions on the
descaler packaging.
2. Pour the solution into the kettle and switch it
on.
3. Allowthesolutiontoboiltwiceandthen
pour it out.
4. Toremovethefinalresiduesoflimescaleand
acetic acid, pour cold water into the kettle
again(uptothe"MAX"mark)andswitchit
on.
5. Pour the water out once it has boiled.
6. Repeattheprocessdescribedunderpoints
4-5threetimes.
Theappliancenowreadyforuse.
 previous next